• wrx
  • Testing Team
  • Offline
  • Registered: 2006-05-30
  • Posts: 58

Topic: nForce SATA/SATARAID not working

Hey there smile i am just wondering if anyone else has come across this problem or can't work out what's going on. I run a nForce4 ultra board, on using  BASE6.08.3 i have a small problem where once xp is installed if you try to do a restart the system hang's or if you shut the system down it take's about 6-10min. This only happen's with my system setup in a raid 0 config if i use one of the drive's out the raid and load it up to xp, xp work's fine ?? what the!!  anyway to fix this problem just download 6.86_nforce drives run and just install the "nVidia storage drivers" this will fix the problem. I think it might be the IDE driver making it hang, unfortunely i didn't check before running the nforce driver.

Last edited by Bâshrat the Sneaky (2006-08-23 11:43:05)

  • From: Hasselt, Belgium
  • Registered: 2006-05-26
  • Posts: 2,609

Re: nForce SATA/SATARAID not working

Did you note down the driver version that was initially installed? i.e. the version that caused problems. That'd be most useful.

Founder of DriverPacks.net — wimleers.com

Wim Leers's Website

  • wrx
  • Testing Team
  • Offline
  • Registered: 2006-05-30
  • Posts: 58

Re: nForce SATA/SATARAID not working

me bad, it was 4 in the morning !! i'll reload,  and note driver's this time  wink

  • wrx
  • Testing Team
  • Offline
  • Registered: 2006-05-30
  • Posts: 58

Re: nForce SATA/SATARAID not working

ok i'm back this what i found .....

nVidia nForce PATA controller driver       5.10.2600.518    11/2/05
                    RAID  Class controller       5.10.2600.667    1/5/06
                    RAID SATA raid contoller   5.10.2600.666     24/4/06

after you run the nVidia driver pack the only one to chance and fix's my problem is

                   RAID  Class controller       5.10.2600.666    24/4/06

so they roll back ??? anyway is fix's everythink..

  • wrx
  • Testing Team
  • Offline
  • Registered: 2006-05-30
  • Posts: 58

Re: nForce SATA/SATARAID not working

Bâshrat the Sneaky where did u get the RAID  Class controller       5.10.2600.667    1/5/06  from  ???? i just throught the nVidia drivers and i can't find it in there ...

  • wrx
  • Testing Team
  • Offline
  • Registered: 2006-05-30
  • Posts: 58

Re: nForce SATA/SATARAID not working

Bâshrat the Sneaky i just found the problem smile  for some reason it's intergrating the DP_MassStorage_wnt5_x86-32_608\D\M\N\590SLI\R driver have a look at the .inf file RAID  Class controller  is "5.10.2600.667"


just found this http://downloads.guru3d.com/download.php?det=1446    but there runnig all .667 drivers ..... this maybe why it intergrate .667 being a newer driver instead of the .666 what do u think??

Last edited by wrx (2006-08-20 18:06:24)

  • From: Hasselt, Belgium
  • Registered: 2006-05-26
  • Posts: 2,609

Re: nForce SATA/SATARAID not working

I'll compare the hwids and report back. Could you also post your DPsFnshr.log? Since the hwids can be found in it.

Founder of DriverPacks.net — wimleers.com

Wim Leers's Website

  • wrx
  • Testing Team
  • Offline
  • Registered: 2006-05-30
  • Posts: 58

Re: nForce SATA/SATARAID not working

one log 

2006-08-20 11:57:20 : <INIT> DriverPacks Finisher 6.08.3 initialized.
2006-08-20 11:57:20 : <INIT> Detected platform wnt5_x86-32.
2006-08-20 11:57:20 : <INIT> Start logging of the HWIDs for relevant devices present in this system.
2006-08-20 11:57:20 : <INIT> 1. ACPI devices

ACPI\AUTHENTICAMD_-_X86_FAMILY_15_MODEL_39\_0               : AMD Opteron(tm) Processor 146   
ACPI\FIXEDBUTTON\2&DABA3FF&0                                : ACPI Fixed Feature Button
ACPI\PNP0000\3&2411E6FE&0                                   : Programmable interrupt controller
ACPI\PNP0100\3&2411E6FE&0                                   : System timer
ACPI\PNP0200\3&2411E6FE&0                                   : Direct memory access controller
ACPI\PNP0303\3&2411E6FE&0                                   : Standard 101/102-Key or Microsoft Natural PS/2 Keyboard
ACPI\PNP0800\3&2411E6FE&0                                   : System speaker
ACPI\PNP0A08\1                                              : PCI bus
ACPI\PNP0B00\3&2411E6FE&0                                   : System CMOS/real time clock
ACPI\PNP0C01\2&DABA3FF&0                                    : System board
ACPI\PNP0C02\1                                              : Motherboard resources
ACPI\PNP0C02\4                                              : Motherboard resources
ACPI\PNP0C02\5                                              : Motherboard resources
ACPI\PNP0C04\3&2411E6FE&0                                   : Numeric data processor
ACPI\PNP0C0C\2&DABA3FF&0                                    : ACPI Power Button
ACPI\_NVRAIDBUS\3&2411E6FE&0                                : NVIDIA nForce(tm) RAID Class Controller
ACPI_HAL\PNP0C08\0                                          : Microsoft ACPI-Compliant System
ROOT\ACPI_HAL\0000                                          : ACPI Uniprocessor PC
18 matching device(s) found.

2006-08-20 11:57:20 : <INIT> 2. PCI devices

PCI\VEN_1002&DEV_554B&SUBSYS_131018BC&REV_00\4&243D7BD0&0&0070: RADEON X800GT 
PCI\VEN_1002&DEV_556B&SUBSYS_131118BC&REV_00\4&243D7BD0&0&0170: RADEON X800GT Secondary 
PCI\VEN_1022&DEV_1100&SUBSYS_00000000&REV_00\3&2411E6FE&0&C0: PCI standard host CPU bridge
PCI\VEN_1022&DEV_1101&SUBSYS_00000000&REV_00\3&2411E6FE&0&C1: PCI standard host CPU bridge
PCI\VEN_1022&DEV_1102&SUBSYS_00000000&REV_00\3&2411E6FE&0&C2: PCI standard host CPU bridge
PCI\VEN_1022&DEV_1103&SUBSYS_00000000&REV_00\3&2411E6FE&0&C3: PCI standard host CPU bridge
PCI\VEN_104C&DEV_8023&SUBSYS_1C0C147B&REV_00\4&13699180&0&3848: Texas Instruments OHCI Compliant IEEE 1394 Host Controller
PCI\VEN_10DE&DEV_0050&SUBSYS_00000000&REV_A3\3&2411E6FE&0&08: PCI standard ISA bridge
PCI\VEN_10DE&DEV_0052&SUBSYS_1C0C147B&REV_A2\3&2411E6FE&0&09: NVIDIA nForce PCI System Management
PCI\VEN_10DE&DEV_0053&SUBSYS_1C0C147B&REV_A2\3&2411E6FE&0&30: NVIDIA nForce4 Parallel ATA Controller
PCI\VEN_10DE&DEV_0054&SUBSYS_1C0C147B&REV_A3\3&2411E6FE&0&38: NVIDIA nForce4 Serial ATA RAID Controller
PCI\VEN_10DE&DEV_0055&SUBSYS_1C0C147B&REV_A3\3&2411E6FE&0&40: NVIDIA nForce4 Serial ATA RAID Controller
PCI\VEN_10DE&DEV_0057&SUBSYS_1C0C147B&REV_A3\3&2411E6FE&0&50: NVIDIA Network Bus Enumerator
PCI\VEN_10DE&DEV_0059&SUBSYS_1C0C147B&REV_A2\3&2411E6FE&0&20: Realtek AC'97 Audio
PCI\VEN_10DE&DEV_005A&SUBSYS_1C0C147B&REV_A2\3&2411E6FE&0&10: Standard OpenHCD USB Host Controller
PCI\VEN_10DE&DEV_005B&SUBSYS_1C0C147B&REV_A3\3&2411E6FE&0&11: Standard Enhanced PCI to USB Host Controller
PCI\VEN_10DE&DEV_005C&SUBSYS_00000000&REV_A2\3&2411E6FE&0&48: PCI standard PCI-to-PCI bridge
PCI\VEN_10DE&DEV_005D&SUBSYS_00000000&REV_A3\3&2411E6FE&0&58: nForce4 PCI-Express Root Port
PCI\VEN_10DE&DEV_005D&SUBSYS_00000000&REV_A3\3&2411E6FE&0&60: nForce4 PCI-Express Root Port
PCI\VEN_10DE&DEV_005D&SUBSYS_00000000&REV_A3\3&2411E6FE&0&68: nForce4 PCI-Express Root Port
PCI\VEN_10DE&DEV_005D&SUBSYS_00000000&REV_A3\3&2411E6FE&0&70: nForce4 PCI-Express Root Port
PCI\VEN_10DE&DEV_005E&SUBSYS_1C0C147B&REV_A3\3&2411E6FE&0&00: nForce4 HyperTransport Bridge
PCI\VEN_1814&DEV_0201&SUBSYS_68341462&REV_01\4&13699180&0&4048: 802.11g PCI Wireless Network Adapter
23 matching device(s) found.

2006-08-20 11:57:20 : <INIT> 3. HDAUDIO devices

No matching devices found.

2006-08-20 11:57:20 : <INIT> 4. USB devices

USB\ROOT_HUB\4&196DF1A4&0                                   : USB Root Hub
USB\ROOT_HUB20\4&2AC2AB9&0                                  : USB Root Hub
USB\VID_043D&PID_0057\5&2B3ABD2C&0&4                        : USB Printing Support
USB\VID_0451&PID_2036\5&2B3ABD2C&0&3                        : Generic USB Hub
USB\VID_046D&PID_C705\181D2B                                : USB Composite Device
USB\VID_046D&PID_C705&MI_00\7&327CE1D&0&0000                : USB Human Interface Device
USB\VID_046D&PID_C705&MI_01\7&327CE1D&0&0001                : USB Human Interface Device
USB\VID_05E3&PID_0710\000000009144                          : USB Mass Storage Device
USB\VID_0AC8&PID_301B\5&2B3ABD2C&0&1                        : VIMICRO USB PC Camera 301x
USBPRINT\LEXMARKLEXMARK_Z25-Z35\6&BF9A1AE&0&USB001          : LexmarkLexmark Z25-Z35
USBSTOR\DISK&VEN_GENERIC&PROD_STORAGE_DEVICE&REV_9144\000000009144&0: Generic STORAGE DEVICE USB Device
USBSTOR\DISK&VEN_GENERIC&PROD_STORAGE_DEVICE&REV_9144\000000009144&1: Generic STORAGE DEVICE USB Device
USBSTOR\DISK&VEN_GENERIC&PROD_STORAGE_DEVICE&REV_9144\000000009144&2: Generic STORAGE DEVICE USB Device
USBSTOR\DISK&VEN_GENERIC&PROD_STORAGE_DEVICE&REV_9144\000000009144&3: Generic STORAGE DEVICE USB Device
14 matching device(s) found.

2006-08-20 11:57:20 : <INIT> Logging of HWIDs complete.
2006-08-20 11:57:20 : <INIT> Processed settings.
2006-08-20 11:57:21 : <FLTR> Collected the HWIDs for this system.
2006-08-20 11:57:21 : <FLTR> Verifying requirements for exception [wnt5_x86-32__0001__D-G-A-1] (1 of 11 exceptions).
2006-08-20 11:57:21 : <FLTR> 	1. tagFiles (ALL tagFiles must be found)
2006-08-20 11:57:21 : <FLTR> 		Found tagfile "C:\ATICCC.ins" (1/2).
2006-08-20 11:57:21 : <FLTR> 		Found tagfile "C:\D\G\A\1\ATICCC.exe" (2/2).
2006-08-20 11:57:21 : <FLTR> 	4. +infFiles (ANY +infFiles must matched
2006-08-20 11:57:21 : <FLTR> 		Wildcard specified for +infFiles requirement: scan for .inf files (1 of 1 +infFiles).
2006-08-20 11:57:21 : <FLTR> 		Checking .inf file 'C:\D\G\A\1\C2_34826.inf'.
2006-08-20 11:57:21 : <FLTR> 		Matched +infFile'C:\D\G\A\1\C2_34826.inf' through the HWID "PCI\VEN_1002&DEV_554B" (original HWID: "PCI\VEN_1002&DEV_554B&SUBSYS_131018BC&REV_00").
2006-08-20 11:57:21 : <FLTR> 	=> All requirements for exception [wnt5_x86-32__0001__D-G-A-1] have been met!
2006-08-20 11:57:21 : <FLTR> Verifying requirements for exception [wnt5_x86-32__0002__D-G-A-1] (2 of 11 exceptions).
2006-08-20 11:57:21 : <FLTR> 	1. tagFiles (ALL tagFiles must be found)
2006-08-20 11:57:21 : <FLTR> 		! Could not find tagfile 'C:\ATICCP.ins' (1 of 2 tagfiles).
2006-08-20 11:57:21 : <FLTR> 	=> This exception will not be applied.
2006-08-20 11:57:21 : <FLTR> Verifying requirements for exception [wnt5_x86-32__0021__D-G-A-2] (3 of 11 exceptions).
2006-08-20 11:57:21 : <FLTR> 	1. tagFiles (ALL tagFiles must be found)
2006-08-20 11:57:21 : <FLTR> 		Found tagfile "C:\ATICCC.ins" (1/2).
2006-08-20 11:57:21 : <FLTR> 		Found tagfile "C:\D\G\A\1\ATICCC.exe" (2/2).
2006-08-20 11:57:21 : <FLTR> 	4. +infFiles (ANY +infFiles must matched
2006-08-20 11:57:21 : <FLTR> 		! Could not match any of the +infFiles.
2006-08-20 11:57:21 : <FLTR> 	=> This exception will not be applied.
2006-08-20 11:57:21 : <FLTR> Verifying requirements for exception [wnt5_x86-32__0022__D-G-A-2] (4 of 11 exceptions).
2006-08-20 11:57:21 : <FLTR> 	1. tagFiles (ALL tagFiles must be found)
2006-08-20 11:57:21 : <FLTR> 		! Could not find tagfile 'C:\ATICCP.ins' (1 of 2 tagfiles).
2006-08-20 11:57:21 : <FLTR> 	=> This exception will not be applied.
2006-08-20 11:57:21 : <FLTR> Verifying requirements for exception [wnt5_x86-32__0006__D-L-NV-123] (5 of 11 exceptions).
2006-08-20 11:57:21 : <FLTR> 	2. +hwids (ANY +hwids must matched
2006-08-20 11:57:21 : <FLTR> 		! Could not match any of the +hwids.
2006-08-20 11:57:21 : <FLTR> 	=> This exception will not be applied.
2006-08-20 11:57:21 : <FLTR> Verifying requirements for exception [wnt5_x86-32__0007__D-S-CR-1] (6 of 11 exceptions).
2006-08-20 11:57:21 : <FLTR> 	1. tagFiles (ALL tagFiles must be found)
2006-08-20 11:57:21 : <FLTR> 		! Could not find tagfile 'C:\WINDOWS\system32\drivers\ha20x2k.sys' (1 of 2 tagfiles).
2006-08-20 11:57:21 : <FLTR> 	=> This exception will not be applied.
2006-08-20 11:57:21 : <FLTR> Verifying requirements for exception [wnt5_x86-32__0008__D-S-CR-2] (7 of 11 exceptions).
2006-08-20 11:57:21 : <FLTR> 	1. tagFiles (ALL tagFiles must be found)
2006-08-20 11:57:21 : <FLTR> 		! Could not find tagfile 'C:\WINDOWS\system32\drivers\ha10x2k.sys' (1 of 3 tagfiles).
2006-08-20 11:57:21 : <FLTR> 	=> This exception will not be applied.
2006-08-20 11:57:21 : <FLTR> Verifying requirements for exception [wnt5_x86-32__0009__D-S-CR-3] (8 of 11 exceptions).
2006-08-20 11:57:21 : <FLTR> 	1. tagFiles (ALL tagFiles must be found)
2006-08-20 11:57:21 : <FLTR> 		! Could not find tagfile 'C:\WINDOWS\system32\drivers\P17.sys"' (1 of 2 tagfiles).
2006-08-20 11:57:21 : <FLTR> 	=> This exception will not be applied.
2006-08-20 11:57:21 : <FLTR> Verifying requirements for exception [wnt5_x86-32__0011__D-S-N] (9 of 11 exceptions).
2006-08-20 11:57:21 : <FLTR> 	1. tagFiles (ALL tagFiles must be found)
2006-08-20 11:57:21 : <FLTR> 		! Could not find tagfile 'C:\WINDOWS\system32\drivers\nvapu.sys' (1 of 1 tagfiles).
2006-08-20 11:57:21 : <FLTR> 	=> This exception will not be applied.
2006-08-20 11:57:21 : <FLTR> Verifying requirements for exception [wnt5_x86-32__0019__D-S-V-1] (10 of 11 exceptions).
2006-08-20 11:57:21 : <FLTR> 	1. tagFiles (ALL tagFiles must be found)
2006-08-20 11:57:21 : <FLTR> 		! Could not find tagfile 'C:\WINDOWS\system32\drivers\envysens.sys' (1 of 1 tagfiles).
2006-08-20 11:57:21 : <FLTR> 	=> This exception will not be applied.
2006-08-20 11:57:21 : <FLTR> Verifying requirements for exception [wnt5_x86-32__0020__D-S-V-2] (11 of 11 exceptions).
2006-08-20 11:57:21 : <FLTR> 	1. tagFiles (ALL tagFiles must be found)
2006-08-20 11:57:21 : <FLTR> 		! Could not find tagfile 'C:\WINDOWS\system32\drivers\vinyl97.sys' (1 of 2 tagfiles).
2006-08-20 11:57:21 : <FLTR> 	=> This exception will not be applied.
2006-08-20 11:57:21 : <FLTR> Finished filtering exceptions.
2006-08-20 11:57:21 : <EXEC> Executing all commands (4) for exception [wnt5_x86-32__0001__D-G-A-1].
2006-08-20 11:57:21 : <EXEC> 	Executing command 1 of 4: "%DPSROOT%\D\G\A\1\ATICCC.exe -y -o"%DPSTMP%"
2006-08-20 11:57:27 : <EXEC> 		No STDOUT output occurred.
2006-08-20 11:57:27 : <EXEC> 	Executing command 2 of 4: "msiexec /i %DPSTMP%\ISScript9.Msi /qn /norestart"
2006-08-20 11:57:28 : <EXEC> 		No STDOUT output occurred.
2006-08-20 11:57:28 : <EXEC> 	Executing command 3 of 4: "msiexec /i %DPSTMP%\ATICCC.msi /qn /norestart"
2006-08-20 11:57:48 : <EXEC> 		No STDOUT output occurred.
2006-08-20 11:57:48 : <EXEC> 	Executing command 4 of 4: "rd /s /q "%DPSTMP%"
2006-08-20 11:57:48 : <EXEC> 		No STDOUT output occurred.
2006-08-20 11:57:48 : <EXEC> No exceptions left to execute: none have met all requirements!
2006-08-20 11:57:50 : <CLNP> Deleted the DriverPacks, which were located in 'C:\D'.
2006-08-20 11:57:50 : <CLNP> Deleted 'C:\hwids.dat'!
2006-08-20 11:57:50 : <CLNP> Deleted 'C:\DPsFnshr.ini'!
2006-08-20 11:57:50 : <CLNP> Deleted 'C:\devcon.exe'!
2006-08-20 11:57:50 : <CLNP> Deleted 'C:\makePNF.exe'!
2006-08-20 11:57:50 : <CLNP> Deleted 'C:\addUsepmtimer.exe'!
2006-08-20 11:57:50 : <CLNP> Deleted 'C:\ATICCC.ins'!
2006-08-20 11:57:50 : <CLNP> Added new value to the RunOnce key in the registry: the DriverPacks Finisher itself will get deleted after the next reboot.
2006-08-20 11:57:50 : Program terminated.
  • wrx
  • Testing Team
  • Offline
  • Registered: 2006-05-30
  • Posts: 58

Re: nForce SATA/SATARAID not working

Hey Bâshrat the Sneaky if i unzip the massstorage DP, replace the the 590SLI drivers with nF4 drivers, and repack would that work for the time being??? 

Also fyi  Im using "5.10.2600.667" instaed of the "5.10.2600.666" drives all around at the moment and they seam to work fine smile

Last edited by wrx (2006-08-22 03:46:46)

  • From: Hasselt, Belgium
  • Registered: 2006-05-26
  • Posts: 2,609

Re: nForce SATA/SATARAID not working

wrx wrote:

Hey Bâshrat the Sneaky if i unzip the massstorage DP, replace the the 590SLI drivers with nF4 drivers, and repack would that work for the time being??? 

Also fyi  Im using "5.10.2600.667" instaed of the "5.10.2600.666" drives all around at the moment and they seam to work fine smile

So instead of this:

wrx wrote:

RAID  Class controller       5.10.2600.667    1/5/06
                    RAID SATA raid contoller   5.10.2600.666     24/4/06

... you're now using this:

me wrote:

RAID  Class controller       5.10.2600.667    1/5/06
                    RAID SATA raid contoller   5.10.2600.667    1/5/06

... right?

Founder of DriverPacks.net — wimleers.com

Wim Leers's Website

11 Reply by wrx

  • wrx
  • Testing Team
  • Offline
  • Registered: 2006-05-30
  • Posts: 58

Re: nForce SATA/SATARAID not working

Spot on mate smile

12 Reply by wrx

  • wrx
  • Testing Team
  • Offline
  • Registered: 2006-05-30
  • Posts: 58

Re: nForce SATA/SATARAID not working

Hey if i go devices manager - Nvidia nForce Serial ATA controller properties - Drivers -update driver - fine one driver - then unpack your DP -  then UNTICKED "Show compatible hardware" it show me 2 listing for the 590/570/550 SATA controller  .666 & .667

with the Raid Class controller with show compaitble hardware TICKED it shows 2 version again 5.10.2600.666 & 667 this where i would say it's getting confused,......

i have so screen shots but i cant work out how to upload them if u want to have a look just let me know smile

ps this was all done on 6.08.5

  • From: Hasselt, Belgium
  • Registered: 2006-05-26
  • Posts: 2,609

Re: nForce SATA/SATARAID not working

wrx wrote:

Hey if i go devices manager - Nvidia nForce Serial ATA controller properties - Drivers -update driver - fine one driver - then unpack your DP -  then UNTICKED "Show compatible hardware" it show me 2 listing for the 590/570/550 SATA controller  .666 & .667

with the Raid Class controller with show compaitble hardware TICKED it shows 2 version again 5.10.2600.666 & 667 this where i would say it's getting confused,......

i have so screen shots but i cant work out how to upload them if u want to have a look just let me know smile

ps this was all done on 6.08.5

I'm not sure I understand what your point is... Please clarify!

Founder of DriverPacks.net — wimleers.com

Wim Leers's Website

14 Reply by wrx

  • wrx
  • Testing Team
  • Offline
  • Registered: 2006-05-30
  • Posts: 58

Re: nForce SATA/SATARAID not working

This is what my pc shows in hard ware devices

By default the computer loads NVidia nForce4 Serial ata raid controller    5.10.2600.666    24/4/06

but if you go into DM and untick   "show compatible hardware"    there are three drivers for the NVidia nForce Serial ATA Controlroller that the computer can chose from

    NVidia nForce 590/570/55  Serial ATA Controlroller  5.10.2600.667      1/5/06   not compatible hardware
              &
    NVidia nForce 590/570/55 Serial ATA Controlroller   5.10.2600.666    24/4/06   not compatible hardware
              &
                  NVidia nForce4 Serial ata raid controller    5.10.2600.666    24/4/06   compatible hardware





ok now we move on to the  nVidia nForce Raid class controller there are also 2 choses the computer can chose from   but loads by default   nVidia nForce Raid class controller 5.10.2600.667    1/5/06

           nVidia nForce Raid class controller 5.10.2600.667    1/5/06     compatible hardware
                                            &
          nVidia nForce Raid class controller 5.10.2600.666    24/4/06     compatible hardware

now both of these show they are compatible drivers, so it load .667 being newer and the 
NVidia nForce Serial ATA Controlroller loads    nForce4 .666  which is where u get a driver miss match which then cause's the problem of not shutting down 

It a nVidia problem not DP problem hey it just unfortunaly there are the same ......   smile

Last edited by wrx (2006-08-22 19:12:39)

15 Reply by wrx

  • wrx
  • Testing Team
  • Offline
  • Registered: 2006-05-30
  • Posts: 58

Re: nForce SATA/SATARAID not working

Just to let you know I unpacked your MassStorage DP Deleted the  590sli drivers, repacked and now the correct drivers are installed straight away  (all .666) wink

  • From: Hasselt, Belgium
  • Registered: 2006-05-26
  • Posts: 2,609

Re: nForce SATA/SATARAID not working

There are 2 ways to solve this. One that will work immediately: using a modified driver that supports ALL devices at once. The other, hard way is to force the installation of a certain driver through the Finisher. But how to detect when a valid system is present? But that's not the core problem: this is a 'SCSI Miniport Driver', which cannot be updated without a reboot.

Anyhow, there are less complications and there will be less problems if I use a modified driver. I had to break my own policy eventually I guess... tongue

Founder of DriverPacks.net — wimleers.com

Wim Leers's Website

  • muiz
  • Vista / 7/8 Driverpacks Team
  • Offline
  • From: Netherlands
  • Registered: 2006-07-01
  • Posts: 1,555

Re: nForce SATA/SATARAID not working

Finaly bashrat gets the point.
Better a beta or modified driver then BSOD.

wink

http://d1syubgj0w3cyv.cloudfront.net/cdn/farfuture/VVyo3dzRp1allVk-OCdyukcaj701mcdrrsdDOyX2wK8/perpetual:forever/userbar/admin-1.png
DONATE!
HWID's Tool     Read BEFORE you post

18 Reply by wrx

  • wrx
  • Testing Team
  • Offline
  • Registered: 2006-05-30
  • Posts: 58

Re: nForce SATA/SATARAID not working

I'm all for the modified or beta driver smile    and If people want to run other drivers then they can just run a manual update later...

  • From: Hasselt, Belgium
  • Registered: 2006-05-26
  • Posts: 2,609

Re: nForce SATA/SATARAID not working

@muiz3: it was working in the past... it is no longer today, so that's why I've decided this wink

Founder of DriverPacks.net — wimleers.com

Wim Leers's Website

  • muiz
  • Vista / 7/8 Driverpacks Team
  • Offline
  • From: Netherlands
  • Registered: 2006-07-01
  • Posts: 1,555

Re: nForce SATA/SATARAID not working

cant wait...........

http://d1syubgj0w3cyv.cloudfront.net/cdn/farfuture/VVyo3dzRp1allVk-OCdyukcaj701mcdrrsdDOyX2wK8/perpetual:forever/userbar/admin-1.png
DONATE!
HWID's Tool     Read BEFORE you post
  • muiz
  • Vista / 7/8 Driverpacks Team
  • Offline
  • From: Netherlands
  • Registered: 2006-07-01
  • Posts: 1,555

Re: nForce SATA/SATARAID not working

New version 6.08.6! worked !!!

Instead of a double post ,read here :

http://forum.driverpacks.net/viewtopic. … 3533#p3533

Last edited by muiz3 (2006-08-28 01:52:46)

http://d1syubgj0w3cyv.cloudfront.net/cdn/farfuture/VVyo3dzRp1allVk-OCdyukcaj701mcdrrsdDOyX2wK8/perpetual:forever/userbar/admin-1.png
DONATE!
HWID's Tool     Read BEFORE you post
  • From: Hasselt, Belgium
  • Registered: 2006-05-26
  • Posts: 2,609

Re: nForce SATA/SATARAID not working

This problem is specific to the HWIDs that are shared between the 666 and 667 driver. So the problem is not yet completely solved.

Founder of DriverPacks.net — wimleers.com

Wim Leers's Website