[ Closed ] [SOLVED] SiI 3112r controller doesnt work: 0x7B BSOD (Page 3 of 5)

no joy 4 me...

haha joy for me this morn, i got it to work, made a few changes, now i gotta figure which changes made it work
bbl

edit:
it seems adding si3112r.sys to \i386 (or compressed (.sy_)) works for me...
i am now able to see the raid partitions yippeeee...
this was with the latest 1.0.56.1 driver from the latest mass storage Driverpack (method 1)

bios - 4276 sil3112a bios in trats  d27_619R2_2T bios for the NF7S-v2
(found here )

Last edited by googs (2006-08-20 15:52:58)

I have the same problem but with a different controller. Mine is Jmicron JMB360 (ASRock 939Dual-SATA2) and I have the BSOD 0x7B when I try to install Winxp. This issue is related only when I have update my unattended cd with the latest driverpacks that you have released. With previous version I haven't had any problem and the installation of Winxp is ok. I can't help you with hwid, because I can't install Winxp, sorry.

And sorry for my bad english

Last edited by S3pHiroTh (2006-08-21 03:36:46)

Bâshrat, I want to ask you a question about this problem. I have mentioned above that I have Jmicron JMB360 controller. After I have slipstreamed the masstorage package in text mode, there are files for each controller compressed in I386 directory, right? Do you have used "makecab" command for compress those files? I have make a my personal (for verify if is a compression problem) Jahci.sy_ file. The file, slipstreamed with your app, is 13.920 bytes, mine is 15.275 bytes, I have used the "makecab" command. This afternoon when I'll go home I'll try if the BSOD 0x07B persists

I have found this also: http://support.microsoft.com/?scid=kb%3 … 6&y=19
Maybe it can help. I hope

EDIT: I have tried but without success...

Last edited by S3pHiroTh (2006-08-23 06:14:54)

Nope, it's only for your controller. But I did not know these devices had the same HWIDs!!!

Why I didn't check that? Their names, as well as their drivers, are completely different, as you can see:

Will fix it through using the CC_104 and CC_106 suffixes.

Greetings,

I have the same problem. A couple of months ago I used mass-storage pack 603.1 into an XP SP2 cd to install on a Silicon Image 378 onboard SATA/RAID controller. I recreated a similar CD with 6.08.7 mass-storage, chipset and LAN. This caused a BSOD on 'starting windows' in text mode setup on two machines one wit the 378 and the other an asus P5N32-SLI (nforce4 / Silicon image something again).

I used 'Method 2' of intergration all times. I've not had a chance to experiement with others, I just wanted to let you know there is definately something odd about 6.08.7

sorry bout the pause, havent had a chance to get back to it yet Bash,

no way to nlite, its crap for me, all the combinations of removals ive tried with it just cause me grief with errors so ive given nlite the flick, just using driverpacks and ryanvms updates...(not worried about the extra size as using dvd...

and yes, the latest driver when slipstreamed normally wouldnt work for me, until i put a copy of that file into i386, with method 1, bit busy at the moment to get back into it, when i do i'll be bak to let u know how i go

Has nothing to do with this problem !

For the rest :

Silicon has new drivers , maybe that will help.

Last edited by muiz3 (2006-09-17 03:24:09)

DONATE!
HWID's Tool     Read BEFORE you post

Bump!  It's nice to see others having the same problem as me!  For a while I thought I was alone on this till I found this forum!
Hi guys, total newb here to driverpacks and slipstreamed windows installs...  So bare with me...  My friend gave me a slipstreamed disc he made, it's entitled the "eXPirence" edition... It has the driverpacks from here in it. 

I have a 3112r raid control controlling two identical SATA discs running in RAID1 Mirrored.  The raid controller is an offboard PCI card.  I actually have two different cards with the same 3112r chipset... I've had the same issue with both of them.  Using this DVD to install windows on this array causes two issues which match identically with the problems mentioned here...

1.  When windows brings up my drive list, I see both of my drives as separate partitions, instead of just one - like it's recognizing the array discs uniquely instead of as one mirrored array.
2.  When windows is done copying files to the drive and performs it's first reboot, I get the 0x7B BSOD.

Doing F6 with this distrib on initial setup, seems to be ignored.  It still uses the driver on the DVD instead.  I  can use my floppy with the latest (I think it's .56) driver using other windows distribs and it works ok. 

Here are my hardware ID's. I created a temporary install of windows to run the hardware ID tool hoping maybe it will help others out...

 
=========== 
PCI devices 
=========== 
 
 
PCI\VEN_1095&DEV_3112&SUBSYS_61121095&REV_02\3&13C0B0C5&0&28: Silicon Image SiI 3112 SATARaid Controller
PCI\VEN_1106&DEV_0571&SUBSYS_05711106&REV_06\3&13C0B0C5&0&89: VIA Bus Master IDE Controller
PCI\VEN_1106&DEV_3038&SUBSYS_30381106&REV_80\3&13C0B0C5&0&80: VIA Rev 5 or later USB Universal Host Controller
PCI\VEN_1106&DEV_3038&SUBSYS_30381106&REV_80\3&13C0B0C5&0&81: VIA Rev 5 or later USB Universal Host Controller
PCI\VEN_1106&DEV_3038&SUBSYS_30381106&REV_80\3&13C0B0C5&0&82: VIA Rev 5 or later USB Universal Host Controller
PCI\VEN_1106&DEV_3059&SUBSYS_78701462&REV_50\3&13C0B0C5&0&8D: Vinyl AC'97 Codec Combo Driver (WDM)
PCI\VEN_1106&DEV_3065&SUBSYS_C01C1462&REV_74\3&13C0B0C5&0&90: VIA Rhine II Fast Ethernet Adapter
PCI\VEN_1106&DEV_3104&SUBSYS_31041106&REV_82\3&13C0B0C5&0&83: VIA USB Enhanced Host Controller
PCI\VEN_1106&DEV_3148&SUBSYS_00000000&REV_00\3&13C0B0C5&0&00: VIA Standard Host Bridge
PCI\VEN_1106&DEV_3177&SUBSYS_00000000&REV_00\3&13C0B0C5&0&88: VIA Standard PCI to ISA Bridge
PCI\VEN_1106&DEV_B091&SUBSYS_00000000&REV_00\3&13C0B0C5&0&08: VIA CPU to AGP Controller
PCI\VEN_5333&DEV_8D04&SUBSYS_78701462&REV_00\4&82C770E&0&0008: S3 Graphics ProSavageDDR (Microsoft Corporation)
12 matching device(s) found.
 
 
=========== 
USB devices 
=========== 
 
USB\ROOT_HUB\4&13464B3C&0                                   : USB Root Hub
USB\ROOT_HUB\4&25FFFBE1&0                                   : USB Root Hub
USB\ROOT_HUB\4&38B9AC86&0                                   : USB Root Hub
USB\ROOT_HUB20\4&10C9AD9F&0                                 : USB Root Hub
4 matching device(s) found.

What I'm curious on mainly, is what do I have to do with this install, in order to replace the drivers on the CD, with either a newer driverpack, OR  - the ones I got from SiL aka my F6 floppy? I've seen reference to replacing the sil3112r.sy_ file with the .sys file I have from my floppy and reburning the DVD... is it that simple ?  Do I simply just delete the existing .sy_ file, and then copy in the .sys file to replace it off my floppy?  Does it need to be a cab compresed, or renamed as .sy_, or anything like that?  AS I mentioned this is all a little over my head...  Am I better off just getting a newer driverpack and if so... how do I add it to this distrib I already have?   

Thanks in advance everyone!

YES.YES YES YES.......!!!!.. Ruud and I solved the Siliconimage BSOD mistery , after  LOTS of tests , we finaly know wich diver causes the BSOD....

Its the "3ware78k" driver...... or the "3waregsm" will do final test  today....

Time to test this on more machines....Bashrat??

Maybe it caused more problems ,Jmicron , Nforce ...??

Ruud...thx again m8 !!! nice teamwork

Last edited by muiz3 (2007-01-08 13:08:20)

DONATE!
HWID's Tool     Read BEFORE you post

so, if i remove these 3ware, Repack, and test on the Gigabyte royal wich has that sil 3132, I could be of help?
(this did a BSOD too... see)

note, the royal also has a Jmicron chip.. did that no have issues of its own? I sorta forgot.