• Registered: 2008-04-15
  • Posts: 7

Topic: [SLVD] dpms 11.06 for ICH8R(DO) Raid cause 0x0000007B BSOD

Hi DP Team

Struggling with a HW platform to run Windows 2003 Server R2. (always ending in 0x0000007B blue screen)
I boot from a XP-PE USB Stick and the Mass Storage driver works fine at this stage.

Files are added to the HDD in the Target system from a server,
then the system reboot and after showing press F6 to add SCSI and RAID devices the system ending with 0x0000007B blue screen.
(If i Press F6 and add the driver from floppy it still blue screen, using the same floppy/driver as on a clean install from CD)

I Use DPsBASE ver10.06 Mass Storage Ver11.06 (until today i used Mass Storage Ver10.06 that fail the same way)

I built a XP with all the same DP's and everything is OK then. So the problem is only for Server 2003 R2.
I have also done exactly the same before for 2003 Server R2 with other raid systems without the blue screen.

I have the HW to test on if you have any experimental pack version(s) for me try out and report back.

Windows Server 2003 R2 HWid's from clean install from CD and F6 floppy work OK.

=========== 
PCI Devices 
=========== 
PCI\VEN_197B&DEV_2363&SUBSYS_2363197B&REV_02\4&AD3FA96&0&00E4: Standard Dual Channel PCI IDE Controller
PCI\VEN_8086&DEV_104A&SUBSYS_00008086&REV_02\3&2411E6FE&0&C8: Ethernet Controller
PCI\VEN_8086&DEV_244E&SUBSYS_00000000&REV_F2\3&2411E6FE&0&F0: Intel(R) 82801 PCI Bridge - 244E
PCI\VEN_8086&DEV_2814&SUBSYS_00000000&REV_02\3&2411E6FE&0&F8: PCI standard ISA bridge
PCI\VEN_8086&DEV_2822&SUBSYS_28208086&REV_02\3&2411E6FE&0&FA: Intel(R) ICH8R/ICH9R/ICH10R/DO/PCH SATA RAID Controller
PCI\VEN_8086&DEV_2830&SUBSYS_28308086&REV_02\3&2411E6FE&0&E8: Standard Universal PCI to USB Host Controller
PCI\VEN_8086&DEV_2831&SUBSYS_28318086&REV_02\3&2411E6FE&0&E9: Standard Universal PCI to USB Host Controller
PCI\VEN_8086&DEV_2832&SUBSYS_28328086&REV_02\3&2411E6FE&0&EA: Standard Universal PCI to USB Host Controller
PCI\VEN_8086&DEV_2834&SUBSYS_28348086&REV_02\3&2411E6FE&0&D0: Standard Universal PCI to USB Host Controller
PCI\VEN_8086&DEV_2835&SUBSYS_28358086&REV_02\3&2411E6FE&0&D1: Standard Universal PCI to USB Host Controller
PCI\VEN_8086&DEV_2836&SUBSYS_28368086&REV_02\3&2411E6FE&0&EF: Standard Enhanced PCI to USB Host Controller
PCI\VEN_8086&DEV_283A&SUBSYS_283A8086&REV_02\3&2411E6FE&0&D7: Standard Enhanced PCI to USB Host Controller
PCI\VEN_8086&DEV_283E&SUBSYS_283E8086&REV_02\3&2411E6FE&0&FB: SM Bus Controller
PCI\VEN_8086&DEV_283F&SUBSYS_00000000&REV_02\3&2411E6FE&0&E0: PCI standard PCI-to-PCI bridge
PCI\VEN_8086&DEV_2847&SUBSYS_00000000&REV_02\3&2411E6FE&0&E4: PCI standard PCI-to-PCI bridge
PCI\VEN_8086&DEV_284B&SUBSYS_284B8086&REV_02\3&2411E6FE&0&D8: Microsoft UAA Bus Driver for High Definition Audio
PCI\VEN_8086&DEV_2990&SUBSYS_00000000&REV_02\3&2411E6FE&0&00: PCI standard host CPU bridge
PCI\VEN_8086&DEV_2991&SUBSYS_00000000&REV_02\3&2411E6FE&0&08: PCI standard PCI-to-PCI bridge
PCI\VEN_8086&DEV_2992&SUBSYS_29928086&REV_02\3&2411E6FE&0&10: Standard VGA Graphics Adapter
19 matching device(s) found.
 
=========== 
USB Devices 
=========== 
USB\ROOT_HUB\4&2058F10D&0                                   : USB Root Hub
USB\ROOT_HUB\4&22AAEC23&0                                   : USB Root Hub
USB\ROOT_HUB\4&30233BBA&0                                   : USB Root Hub
USB\ROOT_HUB\4&34986906&0                                   : USB Root Hub
USB\ROOT_HUB\4&675EE96&0                                    : USB Root Hub
USB\ROOT_HUB20\4&25D208E9&0                                 : USB Root Hub
USB\ROOT_HUB20\4&2D591607&0                                 : USB Root Hub
USB\VID_0409&PID_0840\000000000001                          : USB Mass Storage Device
USB\VID_0644&PID_0000\5&854B4A3&0&2                         : TEAC USB Floppy
USB\VID_090C&PID_1000\AA04012700013497                      : USB Mass Storage Device
USBSTOR\CDROM&VEN_TSSTCORP&PROD_CD/DVDW_SE-T084L&REV_TS00\000000000001&0: TSSTcorp CD/DVDW SE-T084L USB Device
USBSTOR\DISK&VEN_SMI&PROD_USB_DISK&REV_1100\AA04012700013497&0: SMI USB DISK USB Device
USBSTOR\SFLOPPY&VEN_TEAC&PROD_FD-05PUW&REV_2000\6&16710C54&0: TEAC FD-05PUW USB Device
13 matching device(s) found.
 
============= 
Input Devices 
============= 
No matching devices found.
 
============ 
ACPI Devices 
============ 
ACPI\FIXEDBUTTON\2&DABA3FF&0                                : ACPI Fixed Feature Button
ACPI\GENUINEINTEL_-_X86_FAMILY_6_MODEL_15\_0                : Intel(R) Core(TM)2 Quad CPU           @ 2.40GHz
ACPI\GENUINEINTEL_-_X86_FAMILY_6_MODEL_15\_1                : Intel(R) Core(TM)2 Quad CPU           @ 2.40GHz
ACPI\GENUINEINTEL_-_X86_FAMILY_6_MODEL_15\_2                : Intel(R) Core(TM)2 Quad CPU           @ 2.40GHz
ACPI\GENUINEINTEL_-_X86_FAMILY_6_MODEL_15\_3                : Intel(R) Core(TM)2 Quad CPU           @ 2.40GHz
ACPI\INT0800\4&110C4321&0                                   : Intel(R) 82802 Firmware Hub Device
ACPI\PNP0000\4&110C4321&0                                   : Programmable interrupt controller
ACPI\PNP0100\4&110C4321&0                                   : System timer
ACPI\PNP0200\4&110C4321&0                                   : Direct memory access controller
ACPI\PNP0303\4&110C4321&0                                   : Standard 101/102-Key or Microsoft Natural PS/2 Keyboard
ACPI\PNP0400\4&110C4321&0                                   : Printer Port (LPT1)
ACPI\PNP0501\1                                              : Communications Port (COM1)
ACPI\PNP0501\2                                              : Communications Port (COM2)
ACPI\PNP0501\3                                              : Communications Port (COM3)
ACPI\PNP0501\4                                              : Communications Port (COM4)
ACPI\PNP0700\4&110C4321&0                                   : Standard floppy disk controller
ACPI\PNP0800\4&110C4321&0                                   : System speaker
ACPI\PNP0A08\1                                              : PCI bus
ACPI\PNP0B00\4&110C4321&0                                   : System CMOS/real time clock
ACPI\PNP0C01\2&DABA3FF&0                                    : System board
ACPI\PNP0C02\1                                              : Motherboard resources
ACPI\PNP0C02\2                                              : Motherboard resources
ACPI\PNP0C02\4                                              : Motherboard resources
ACPI\PNP0C04\4&110C4321&0                                   : Numeric data processor
ACPI\PNP0C0B\2&DABA3FF&0                                    : ACPI Fan
ACPI\PNP0C0C\2&DABA3FF&0                                    : ACPI Power Button
ACPI\PNP0F13\4&110C4321&0                                   : PS/2 Compatible Mouse
ACPI\THERMALZONE\THRM                                       : ACPI Thermal Zone
ACPI_HAL\PNP0C08\0                                          : Microsoft ACPI-Compliant System
ROOT\ACPI_HAL\0000                                          : ACPI Multiprocessor PC
30 matching device(s) found.
 
============ 
 HDA Audio 
============ 
HDAUDIO\FUNC_01&VEN_11D4&DEV_1988&SUBSYS_104381E1&REV_1004\4&17F31A78&0&0001: Audio Device on High Definition Audio Bus
1 matching device(s) found.
 
============ 
RAID Devices 
============ 
PCI\VEN_197B&DEV_2363&SUBSYS_2363197B&REV_02\4&AD3FA96&0&00E4
    Name: Standard Dual Channel PCI IDE Controller
    Hardware ID's:
        PCI\VEN_197B&DEV_2363&SUBSYS_2363197B&REV_02
        PCI\VEN_197B&DEV_2363&SUBSYS_2363197B
        PCI\VEN_197B&DEV_2363&CC_010185
        PCI\VEN_197B&DEV_2363&CC_0101
    Compatible ID's:
        PCI\VEN_197B&DEV_2363&REV_02
        PCI\VEN_197B&DEV_2363
        PCI\VEN_197B&CC_010185
        PCI\VEN_197B&CC_0101
        PCI\VEN_197B
        PCI\CC_010185
        PCI\CC_0101
PCI\VEN_8086&DEV_2822&SUBSYS_28208086&REV_02\3&2411E6FE&0&FA
    Name: Intel(R) ICH8R/ICH9R/ICH10R/DO/PCH SATA RAID Controller
    Hardware ID's:
        PCI\VEN_8086&DEV_2822&SUBSYS_28208086&REV_02
        PCI\VEN_8086&DEV_2822&SUBSYS_28208086
        PCI\VEN_8086&DEV_2822&CC_010400
        PCI\VEN_8086&DEV_2822&CC_0104
    Compatible ID's:
        PCI\VEN_8086&DEV_2822&REV_02
        PCI\VEN_8086&DEV_2822
        PCI\VEN_8086&CC_010400
        PCI\VEN_8086&CC_0104
        PCI\VEN_8086
        PCI\CC_010400
        PCI\CC_0104
2 matching device(s) found.

DPs_BASE.ini

[General]
; preferred language
prefLang	= "English"
; yes/no, enable or disable the wizard-style buttons, if not specified: yes
wizardButtons	= "yes"
; yes/no, enable or disable the GUI, if not specified: yes
GUI		= "yes"


[Settings]
; disc/bartpe/multibootDisc
instPlatform	= "disc"
; trailing backslash is allowed, but not necessary
location	= "C:\DriverPacks1.5\x86"
; none/all/select, if select, specify them below, if not specified: all
DriverPacks	= "all"
; 1/2, method to install the DriverPacks, if not specified: 2
DPsMethod	= "2"
; GUIRunOnce/RunOnceEx/custom, if not specified: GUIRunOnce
finisherMethod	= "GUIRunOnce"


; this section is optional!
[OptionalSettings]
; none/all/select/paths/patterns, enable or disable Keep The Drivers (KTD) , if not specified: none
KTD		= "false"
; <path>, to specify a custom KTD cache location, if not specified: default (%SystemRoot%\DriverPacks)
KTDlocation	= "%SystemRoot%\DriverPacks"
; yes/no, enable or disable QuickStream Cache (QSC), if not specified: yes
QSC		= "no"


; this section is optional!
[OptionalSettingsOther]
; CCC/CCP/None, use ATI Catalyst Control Center or ATI Catalyst Control Panel (only relevant when slipstreaming Graphics DriverPack)
; 1/2/3/None, use Nvidia Control Panel - 1 = Old, 2 = New, 3 = Both, None
ATI_cpl		= "CCP"
Nvidia_cpl	= "1"

DPs_BASE.log:

2011-06-22 09:20:00 : <INIT> DriverPacks BASE 10.06 initialized.
2011-06-22 09:20:00 : <INIT> Host environment: WIN_7  X64 on a X64 CPU.
2011-06-22 09:20:00 : <INIT> Created temporary working directory.
2011-06-22 09:20:00 : <INIT> Imported proxy settings from Internet Explorer.
2011-06-22 09:20:00 : <INIT> Start scanning for DriverPacks for the wnt5_x86-32 platform.
2011-06-22 09:20:00 : <INIT> 	Detected DriverPack Chipset 10052!
2011-06-22 09:20:00 : <INIT> 	Detected DriverPack CPU 1005!
2011-06-22 09:20:00 : <INIT> 	Detected DriverPack Graphics A 1005!
2011-06-22 09:20:00 : <INIT> 	Detected DriverPack Graphics B 1005!
2011-06-22 09:20:00 : <INIT> 	Detected DriverPack Graphics C 1005!
2011-06-22 09:20:00 : <INIT> 	Detected DriverPack LAN 1007!
2011-06-22 09:20:00 : <INIT> 	Detected DriverPack Mass Storage 1106!
2011-06-22 09:20:00 : <INIT> 	Detected DriverPack Sound A 1006!
2011-06-22 09:20:00 : <INIT> 	Detected DriverPack Sound B 1006!
2011-06-22 09:20:00 : <INIT> 	Detected DriverPack WLAN 1007!
2011-06-22 09:20:00 : <INIT> 	Detected 3rd Party DriverPack Graphics Languages 1005!
2011-06-22 09:20:00 : <INIT> 	Detected 3rd Party DriverPack Graphics PhysX 1004!
2011-06-22 09:20:00 : <INIT> 	Detected 3rd Party DriverPack Monitor 100711!
2011-06-22 09:20:00 : <INIT> 	Detected 3rd Party DriverPack MoxaSerial 2PassMarkUSBLoopback 140408!
2011-06-22 09:20:00 : <INIT> 	Detected 3rd Party DriverPack Runtimes 1008!
2011-06-22 09:20:00 : <INIT> 	Finished scanning.
2011-06-22 09:20:00 : <INIT> Detected settings file "C:\DriverPacks1.5\DPs_BASE.ini".
2011-06-22 09:20:00 : <INIT> Windows Server 2003, Standard -  Retail SP2 detected.
2011-06-22 09:20:00 : <INIT> wnt5_x86-32_disc is the selected installation platform .
2011-06-22 09:20:00 : <INIT> Imported settings from settings file.
2011-06-22 09:20:00 : <GUI>  Initialized GUI.
2011-06-22 09:20:00 : <GUI>  Created a list of all available language files.
2011-06-22 09:20:00 : <GUI>  Set the last used language, English, as the GUI language.
2011-06-22 09:20:41 : <GUI>  Exported settings to C:\DriverPacks1.5\server2003.ini.
2011-06-22 09:20:51 : <GUI>  Saved settings!
2011-06-22 09:20:51 : <GUI>  Closed GUI.
2011-06-22 09:20:51 : <SEL>  Selected module: mod_slip_w2k3_x86-32_disc_m2.
2011-06-22 09:20:51 : <PREP> Removed all attributes from \I386.
2011-06-22 09:20:51 : <PREP> No previous DriverPacks installation found, Prep stage will be skipped
2011-06-22 09:20:54 : <SLIP> Extracted DriverPack MassStorage to a temporary working directory.
2011-06-22 09:20:54 : <SLIP> C:\DriverPacks1.5\tmp\DPMtmp\DriverPack_MassStorage_wnt5_x86-32.ini
2011-06-22 09:20:54 : <SLIP> Processing Mass Storage files now. This may take a minute.
2011-06-22 09:20:54 : <SLIP> The Driver C:\DriverPacks1.5\x86\I386\amdbusdr could not be backed up
2011-06-22 09:20:54 : <SLIP> The Driver C:\DriverPacks1.5\x86\I386\siside could not be backed up
2011-06-22 09:21:07 : <SLIP> Slipstreamed DriverPack MassStorage text mode driver files.
2011-06-22 09:21:07 : <SLIP> txtsetup.sif Backed-up Successfully
2011-06-22 09:21:08 : <SLIP> dosnet.inf Backed-up Successfully
2011-06-22 09:21:16 : <SLIP> Removed entries from \I386\txtsetup.sif that will be updated.
2011-06-22 09:21:18 : <SLIP> Removed entries from \I386\dosnet.inf that will be updated.
2011-06-22 09:21:48 : <SLIP> Updated \I386\dosnet.inf and \I386\txtsetup.sif to support DP MassStorage text mode drivers.
2011-06-22 09:21:48 : <SLIP> Created necessary directory structure for method 2.
2011-06-22 09:21:48 : <SLIP> Copying files necessary for method 2.
2011-06-22 09:21:48 : <SLIP> Extracted additional files necessary for method 2.
2011-06-22 09:21:48 : <SLIP> expanded setup.ex_ to setuporg.exe
2011-06-22 09:21:48 : <SLIP> SETUP.EX_ Backed-up Successfully
2011-06-22 09:21:48 : <SLIP> Compressed setup.exe to SETUP.EX_.
2011-06-22 09:21:48 : <SLIP> Method 2 setup.ex_ installed
2011-06-22 09:21:48 : <SLIP> Created \I386\presetup.cmd file.
2011-06-22 09:21:49 : <SLIP> Updated \I386\txtsetup.sif to support method 2.
2011-06-22 09:21:49 : <SLIP> Updated \I386\dosnet.inf to support method 2.
2011-06-22 09:21:49 : <SLIP> Copied DriverPack Chipset to \OEM.
2011-06-22 09:21:49 : <SLIP> Copied DriverPack CPU to \OEM.
2011-06-22 09:21:49 : <SLIP> Copied DriverPack Graphics A to \OEM.
2011-06-22 09:21:50 : <SLIP> Copied DriverPack Graphics B to \OEM.
2011-06-22 09:21:51 : <SLIP> Copied DriverPack Graphics C to \OEM.
2011-06-22 09:21:51 : <SLIP> Copied DriverPack LAN to \OEM.
2011-06-22 09:21:51 : <SLIP> Copied DriverPack Mass Storage to \OEM.
2011-06-22 09:21:51 : <SLIP> Copied DriverPack Sound A to \OEM.
2011-06-22 09:21:52 : <SLIP> Copied DriverPack Sound B to \OEM.
2011-06-22 09:21:52 : <SLIP> Copied DriverPack WLAN to \OEM.
2011-06-22 09:21:57 : <SLIP> Renamed DriverPack DP_Graphics_Languages_wnt5_x86-32_1005.7z to DPGL1005.7z in \OEM.
2011-06-22 09:21:57 : <SLIP> Renamed DriverPack DP_Graphics_PhysX_wnt5_x86-32_1004.7z to DPGP1004.7z in \OEM.
2011-06-22 09:21:57 : <SLIP> Renamed DriverPack DP_Monitor_wnt5_x86-32_100711.7z to DP_Monit.7z in \OEM.
2011-06-22 09:21:57 : <SLIP> Renamed DriverPack DP_MoxaSerial_2PassMarkUSBLoopback_wnt5_x86-32_140408.7z to DP_MoxaS.7z in \OEM.
2011-06-22 09:21:57 : <SLIP> Renamed DriverPack DP_Runtimes_wnt5_x86-32_1008.7z to DPGR1008.7z in \OEM.
2011-06-22 09:21:57 : <SLIP> Copied DriverPacks to \OEM.
2011-06-22 09:21:57 : <SLIP> Will not slipstream KB888111 because Service Pack 2 was detected.
2011-06-22 09:21:57 : <SLIP> Updated \I386\winnt.sif to support method 2.
2011-06-22 09:21:57 : <SLIP> Updated DPsFnshr.ini to disable KTD.
2011-06-22 09:21:57 : <SLIP> Updated \I386\winnt.sif's GUIRunOnce section.
2011-06-22 09:21:57 : <SLIP> DP_Install_Tool was copied successfully
2011-06-22 09:21:57 : <SLIP> Slipstream finished in 1 minutes and 6 seconds.
2011-06-22 09:23:14 : <CLNP> Temporary working directory successfully deleted.
- = DriverPacks BASE ini settings used = -
[General]
; preferred language
prefLang	= "English"
; yes/no, enable or disable the wizard-style buttons, if not specified: yes
wizardButtons	= "yes"
; yes/no, enable or disable the GUI, if not specified: yes
GUI		= "yes"


[Settings]
; disc/bartpe/multibootDisc
instPlatform	= "disc"
; trailing backslash is allowed, but not necessary
location	= "C:\DriverPacks1.5\x86"
; none/all/select, if select, specify them below, if not specified: all
DriverPacks	= "all"
; 1/2, method to install the DriverPacks, if not specified: 2
DPsMethod	= "2"
; GUIRunOnce/RunOnceEx/custom, if not specified: GUIRunOnce
finisherMethod	= "GUIRunOnce"


; this section is optional!
[OptionalSettings]
; none/all/select/paths/patterns, enable or disable Keep The Drivers (KTD) , if not specified: none
KTD		= "false"
; <path>, to specify a custom KTD cache location, if not specified: default (%SystemRoot%\DriverPacks)
KTDlocation	= "%SystemRoot%\DriverPacks"
; yes/no, enable or disable QuickStream Cache (QSC), if not specified: yes
QSC		= "no"


; this section is optional!
[OptionalSettingsOther]
; CCC/CCP/None, use ATI Catalyst Control Center or ATI Catalyst Control Panel (only relevant when slipstreaming Graphics DriverPack)
; 1/2/3/None, use Nvidia Control Panel - 1 = Old, 2 = New, 3 = Both, None
ATI_cpl		= "CCP"
Nvidia_cpl	= "1"
2011-06-22 09:23:14 : <CLNP> Create a DPs_Base.log backup @ C:\DriverPacks1.5\LogFiles\DPs_BASE_11-06-22_09-23.log
2011-06-22 09:23:14 : <CLNP> Program terminated.
  • From: Cambridgeshire, UK
  • Registered: 2007-01-27
  • Posts: 6,226

Re: [SLVD] dpms 11.06 for ICH8R(DO) Raid cause 0x0000007B BSOD

According to the Intel documentation, the new 10.5 RST drivers do not support Win2k3, but the older 10.1 drivers do.
10.5 RST link here:
10.1 RST link here:

Intel wrote:

Intel does not plan to develop and offer Windows Server 2003* or Windows Server 2008* drivers for any Intel® Desktop Board.
Source:

I'll look into it more and post a link to a test pack hopefully soon.

Read BEFORE you post.  HWID tool   DriverPacks Tutorial   DONATE!
http://driverpacks.net/userbar/admin-1.png
Not all heroes wear capes, some wear Kevlar!
  • From: Cambridgeshire, UK
  • Registered: 2007-01-27
  • Posts: 6,226

Re: [SLVD] dpms 11.06 for ICH8R(DO) Raid cause 0x0000007B BSOD

Can you please test this experimental pack on your w2k3 build?
DP_MassStorage_wnt5_x86-32_11061b2
link removed

Read BEFORE you post.  HWID tool   DriverPacks Tutorial   DONATE!
http://driverpacks.net/userbar/admin-1.png
Not all heroes wear capes, some wear Kevlar!
  • Registered: 2008-04-15
  • Posts: 7

Re: [SLVD] dpms 11.06 for ICH8R(DO) Raid cause 0x0000007B BSOD

Hi mr_smartepants

Thanks for the experimental pack.
I am sorry to say that i get the same result.
XP ok and Windows 2003 server Blue Screen 07B.

Installing from CDROM and using the driver from I8 and I9 manually with F6 works ok.
When choosing "Intel(R) Desktop/Workstation/Server Express Chipset SATA RAID Controller" from TXTSETUP.OEM

Any idea what to do next ?

Last edited by helgefylla (2011-06-23 23:21:05)

  • From: Cambridgeshire, UK
  • Registered: 2007-01-27
  • Posts: 6,226

Re: [SLVD] dpms 11.06 for ICH8R(DO) Raid cause 0x0000007B BSOD

helgefylla wrote:

DP_MoxaSerial_2PassMarkUSBLoopback_wnt5_x86-32_140408.7z

What the h*ll is that?!?
So which driver are you installing from F6-floppy?

Read BEFORE you post.  HWID tool   DriverPacks Tutorial   DONATE!
http://driverpacks.net/userbar/admin-1.png
Not all heroes wear capes, some wear Kevlar!
  • OverFlow
  • DriverPacks Administrator & BASE Developer
  • Offline
  • From: Cincinnati
  • Registered: 2006-12-02
  • Posts: 6,730

Re: [SLVD] dpms 11.06 for ICH8R(DO) Raid cause 0x0000007B BSOD

I think that driver is for loopback plugs, we used to use "CheckIt" back in the day we had loopbacks for the serial and parallel ports. Checkit would test the output connectors of the serial port to it's input through the loopbacks. We could be certain that the hardware was operating properly. I imagine it's a similar tool used to verify USB ports.

big_smile

the passmark loopbacks prolly verify the ports works and gives a speed test.

DP BartPE Tutorial   DP_BASE Tutorial   HWID's Tool     Read BEFORE you post    UserBars!
http://driverpacks.net/userbar/admin-1.png
The DriverPacks, the DP_Base program, and Support Forum are FREE!.

OverFlow's Website

  • From: Cambridgeshire, UK
  • Registered: 2007-01-27
  • Posts: 6,226

Re: [SLVD] dpms 11.06 for ICH8R(DO) Raid cause 0x0000007B BSOD

I'm wondering if it's the Jmicron drivers causing your problems. 
I'm also confused on how you're installing the OS. 

helgefylla wrote:

Files are added to the HDD in the Target system from a server,
then the system reboot and after showing press F6 to add SCSI and RAID devices the system ending with 0x0000007B blue screen.

So you're not using a USB/disc-based install?  You're using a server-based RIS method?
When does the system blue-screen?  At what point?
Does the install complete without adding any drivers?  Does a SAD2-based driver install work post-install?

Read BEFORE you post.  HWID tool   DriverPacks Tutorial   DONATE!
http://driverpacks.net/userbar/admin-1.png
Not all heroes wear capes, some wear Kevlar!
  • Registered: 2008-04-15
  • Posts: 7

Re: [SLVD] dpms 11.06 for ICH8R(DO) Raid cause 0x0000007B BSOD

Sorry for late reply, been on vacation.

OverFlow: you are correct the "DP_MoxaSerial_2PassMarkUSBLoopback_wnt5_x86-32_140408.7z" is loopback driver to be used with Passmark Burnin Test. Moxa is a serialboard drivers.

mr_smartepants:
So which driver are you installing from F6-floppy
I success with original server 2003 CD with both I8 and I9 found in DP and placed on a F6-floppy (tested each separately)

mr_smartepants:
1. I'm wondering if it's the Jmicron drivers causing your problems.
Agree this might cause problems, but disabling it in Bios do not help sad
And for Win XP there is no problem, only Server 2003....

2. I'm also confused on how you're installing the OS.
I understand this is not the most common way to do it, but i have done this for years.

3. So you're not using a USB/disc-based install?  You're using a server-based RIS method?
I boot from a USB stick with XP WinPE with implemented networking and SCSI/RAID support. Then connect to a server, where the actual install is run from.

What i am able to do is boot from the USB Stick and have access to the disk without problems.
Then i start the pre-install from a server/network share. The disk is partitioned and formatted OK.
Then the Windows pre-install files are copied to the system OK and system restarts.

4. When does the system blue-screen?  At what point?
After the system has reboot as described above in 3. the (Blue) Windows Setup starts
After showing press F6 to add SCSI and RAID devices the system ending with 0x0000007B blue screen.
(Also same thing if i now press F6 and try to add a driver that works from 2003 Server CD install with F6-Floppy as working like described above)

5. Does the install complete without adding any drivers?
If not adding any drivers i also get blue screen

6. Does a SAD2-based driver install work post-install?
Have not been able to check yet.

  • From: Cambridgeshire, UK
  • Registered: 2007-01-27
  • Posts: 6,226

Re: [SLVD] dpms 11.06 for ICH8R(DO) Raid cause 0x0000007B BSOD

That sounds like a convoluted install to me.  You might be better off with an image-based install by using Offline-sysprep.
So, just to eliminate your method from the equation, can you try a traditional disc-based install?  Just use a standard 2003 disc, copy to a folder on the desktop, integrate dpms via DriverPacks BASE using the defaults (check dpms and txtmode), then build the .iso and burn to cdrw or dvd-rw and try that.  I just want to ensure that dpms works on your hardware and not being fouled by your install method.

Read BEFORE you post.  HWID tool   DriverPacks Tutorial   DONATE!
http://driverpacks.net/userbar/admin-1.png
Not all heroes wear capes, some wear Kevlar!
  • Registered: 2008-04-15
  • Posts: 7

Re: [SLVD] dpms 11.06 for ICH8R(DO) Raid cause 0x0000007B BSOD

Did as you said and tested with the disc based install (checked DriverPack MassStorage and txtmode).
Well the install starts, and i can see that different disk controller files are loaded to the system
Setup is loading files (...)

Then i end up with this screen.

Windows Server 2003, Standard Edition Setup
---------------------------------------------------
Setup did not find any hard disk drives installed in your computer.
Make sure any hard disk drives are power on and properly connected
to your computer, and that any disk-related hardware configuration is
correct. This may involve running a manufacturer-supplied diagnostic
or setup program.
Setup cannot continue. To quit Setup, press F3.

I think this is the same as i ended up with in pt. 5 in my last post. (not a blue screen as i wrote)

So i also did a F6-Floppy test with the disc based install (with Mass Storage 11.06)
When choosing "Intel(R) Desktop/Workstation/Server Express Chipset SATA RAID Controller" from TXTSETUP.OEM
I ended up with the same message as above.
Setup did not find any hard disk drives installed in your computer.

Created another DVD with Mass Storage 11.07 when i found that it was available.
Booted and a lot more drivers was loaded. Nice, keep up the good work smile
Unfortunately I ended up with the same message as above.
Setup did not find any hard disk drives installed in your computer.

  • From: Cambridgeshire, UK
  • Registered: 2007-01-27
  • Posts: 6,226

Re: [SLVD] dpms 11.06 for ICH8R(DO) Raid cause 0x0000007B BSOD

OK, well now we're making progress.  Having no drives detected is much better than a BSOD.  The BSOD must be caused by something you're doing to the install process, not DriverPacks.
Hopefully I'll get some time to work out a solution (next week) if someone else doesn't beat me to it.

Read BEFORE you post.  HWID tool   DriverPacks Tutorial   DONATE!
http://driverpacks.net/userbar/admin-1.png
Not all heroes wear capes, some wear Kevlar!
  • From: Cambridgeshire, UK
  • Registered: 2007-01-27
  • Posts: 6,226

Re: [SLVD] dpms 11.06 for ICH8R(DO) Raid cause 0x0000007B BSOD

OK, I need to know what controller your drives are connected to.
When windows setup DOES see the drives, the controller is named in brackets; [jraid] is Jmicron controller, [iastor*] is Intel controller.
What does yours say?

From the jmicron release notes:

// [Notice]
// JMB36X driver got logo of Windows XP, Windows Vista, and Windows 7 since R1.17.49WHQL.

I'm interpreting that as the Jmicron drivers don't work in a server environment.  Can someone prove me wrong?

Read BEFORE you post.  HWID tool   DriverPacks Tutorial   DONATE!
http://driverpacks.net/userbar/admin-1.png
Not all heroes wear capes, some wear Kevlar!
  • OverFlow
  • DriverPacks Administrator & BASE Developer
  • Offline
  • From: Cincinnati
  • Registered: 2006-12-02
  • Posts: 6,730

Re: [SLVD] dpms 11.06 for ICH8R(DO) Raid cause 0x0000007B BSOD

just as a side note...

if you are doing RIS based setup perhaps consider AutoImage by RogueSpear.. it is no longer updated or supported by him but is quite solid and works beautifully with DriverPacks... the forum is still on line and the downloads are still available. Also it is something we are familiar with big_smile.

DP BartPE Tutorial   DP_BASE Tutorial   HWID's Tool     Read BEFORE you post    UserBars!
http://driverpacks.net/userbar/admin-1.png
The DriverPacks, the DP_Base program, and Support Forum are FREE!.

OverFlow's Website

  • Registered: 2008-04-15
  • Posts: 7

Re: [SLVD] dpms 11.06 for ICH8R(DO) Raid cause 0x0000007B BSOD

I was able to locate an old DP_MassStorage version: DP_MassStorage_wnt5_x86-32_805.7z
With this i was able to install the system without problems at all.

Now I'm able to install either Intel Matrix 7.6.0.1011 or Intel Rapid Storage Technology 10.6.0.1002 if i want.

Thanks a lot for all support.
Finally it's solved for me smile