Topic: [REQ] New drivers for IBM ServeRAID Adapters

DriverPack Mass Storage 7.04 currently contains two older versions of the device drivers for the IBM ServeRAID Controllers.
Old 1) IBM ServeRAID 7.00.14 ipsraidn based ServeRAID Adapters for Windows 2000 and Windows XP
Folder D\M\I\1
Section [I-1] in DriverPack_MassStorage_wnt5_x86-32.ini
NOTE: This driver is not intended for Windows 2003 and the corrections are listed below

Old 2) IBM ServeRAID 7.00.14 960 i960-based ServeRAID Adapters for Windows 2000 and Windows XP
Folder D\M\I\2
Section [I-2] in DriverPack_MassStorage_wnt5_x86-32.ini
NOTE: This driver is not intended for Windows 2003 and the corrections are listed below

The updated device drivers are available from the following web page.
http://www-304.ibm.com/jct01004c/system … nd=5000008

If you like, I can e-mail or FTP the newer version of the D\M\I folder

1) Remove the current D\M\I\1 folder and remove the current [I-1} section

2) Remove the current D\M\I\2 folder and remove the current [I-2] section

3) IBM ServeRAID v7.12.11 ipsraidn based ServeRAID Adapters for Windows 2000 and Windows XP
3.1) Download 39y4887.exe from
http://www-304.ibm.com/jct01004c/system … nd=5000008
3.2) Place a blank floppy in your A: drive and run 39y4887.exe. This will create a floppy with the device driver.
3.3) Create a new folder D\M\I\1
3.4) Copy the contents of A:\Windows\win2k_xp\scsi\ppcdrvr to D\M\I\1
3.5) Create a new [I-1] section:

4) IBM ServeRAID v7.12.11 i960-based ServeRAID Adapters for Windows 2000 and Windows XP
4.1) Download 39y4887.exe from
http://www-304.ibm.com/jct01004c/system … nd=5000008
4.2) Place a blank floppy in your A: drive and run 39y4887.exe. This will create a floppy with the device driver.
4.3) Create a new folder D\M\I\2
4.4) Copy the contents of A:\Windows\win2k_xp\scsi\ivdrvr to D\M\I\2
4.5) Create a new [I-2] section:

5) IBM ServeRAID v7.12.11 i960-based ServeRAID Adapters for Windows 2003
5.1)Download ibm_dd_ips_7.12.11_win2k3_i386.zip from
http://www-304.ibm.com/jct01004c/system … nd=5000008
5.2) Extract the contents of the downloaded zip file
5.3) Create a new folder D\M\I\3
5.4) Copy the unzipped files to D\M\I\3
5.5) Create a new [I-3] section

Question: From steps 4 and 5 above, the IBM ServeRAID v7.12.11 i960 driver in step uses the name "nfrd960.sys" for Windows 2000/XP. In step 5, the i960 driver also uses the name "nfrd960.sys" for Windows 2003.  Should we rename nfrd960.sys from step 5 to something else?  Or, is this ok because the .ini file states the skipIfOS values and [I-2] and [I-3] will not be used at the same time?

6) IBM ServeRAID v8.40 8i 8k 8k-l SAS-SATA Adapters for Windows 2000/XP
6.1) Download ibm_dd_aacraid_5.2.0.11829_windows_32-64.exe from
http://www-304.ibm.com/jct01004c/system … nd=5000008
6.2) Extract the contents of the downloaded .exe file
6.3) Create a new folder D\M\I\4
6.4) Copy the unzipped folder \image\disk1\2000-XP to D\M\I\4
6.5) Create a new [I-4] section

7) IBM ServeRAID v8.40 8i 8k 8k-l SAS-SATA Adapters for Windows 2003
7.1) Download ibm_dd_aacraid_5.2.0.11829_windows_32-64.exe from
http://www-304.ibm.com/jct01004c/system … nd=5000008
7.2) Extract the contents of the downloaded .exe file
7.3) Create a new folder D\M\I\5
7.4) Copy the unzipped folder \image\disk1\2003-i386 to D\M\I\5
7.5) Create a new [I-5] section

8) IBM ServeRAID v1.2.5929 8e Adapters for Windows 2000/XP/2003
8.1) Download ibm_dd_hradpxx_1.2.5929_windows_i386.zip from
http://www-304.ibm.com/jct01004c/system … nd=5000008
8.2) Extract the contents of the downloaded .zip file
8.3) Create a new folder D\M\I\6
8.4) Copy the unzipped folder \adp94xx to D\M\I\6
8.5) Create a new [I-6] section


[I-1]
ms_count 			= 1
ms_1_deviceName		= "IBM ipsraidn ServeRAID Adapters (Windows 2000/XP 32-bit)"
ms_1_tag			= "ipsraidn"
ms_1_sysFile		= "ipsraidn.sys"
ms_1_hwids			= "PCI\VEN_1014&DEV_002E&SUBSYS_022E1014&REV_10,PCI\VEN_1014&DEV_002E&SUBSYS_002E1014&REV_0D,PCI\VEN_1014&DEV_002E&SUBSYS_00000000&REV_04,PCI\VEN_1014&DEV_002E&SUBSYS_00000000&REV_03,PCI\VEN_1014&DEV_002E&SUBSYS_00000000&REV_02"
ms_1_isBusExtender	= false
ms_1_exc_disableIfOS= "w2k"
ms_1_exc_replaceIfOS= "w2k"
ms_1_exc_skipIfOS= "w2k3"


[I-2]
ms_count 			= 1
ms_1_deviceName		= "IBM i960-based IBM ServeRAID Adapters (Windows 2000/XP 32-bit)"
ms_1_tag			= "nfrd960"
ms_1_sysFile		= "nfrd960.sys"
ms_1_hwids			= "PCI\VEN_1014&DEV_01BD&SUBSYS_01BE1014,PCI\VEN_1014&DEV_01BD&SUBSYS_01BF1014,PCI\VEN_1014&DEV_01BD&SUBSYS_02081014,PCI\VEN_1014&DEV_01BD&SUBSYS_020E1014,PCI\VEN_1014&DEV_01BD&SUBSYS_02591014,PCI\VEN_9005&DEV_0250&SUBSYS_02791014,PCI\VEN_9005&DEV_0250&SUBSYS_028C1014,PCI\VEN_9005&DEV_0250&SUBSYS_028E1014"
ms_1_isBusExtender	= false
ms_1_exc_disableIfOS= "w2k"
ms_1_exc_skipIfOS= "w2k3"

[I-3]
ms_count 			= 1
ms_1_deviceName		= "IBM i960-based IBM ServeRAID Adapters (Windows 2003 32-bit)"
ms_1_tag			= "nfrd960"
ms_1_sysFile		= "nfrd960.sys"
ms_1_hwids			= "PCI\VEN_1014&DEV_01BD&SUBSYS_02081014,PCI\VEN_1014&DEV_01BD&SUBSYS_020E1014,PCI\VEN_1014&DEV_01BD&SUBSYS_02591014,PCI\VEN_9005&DEV_0250&SUBSYS_02791014,PCI\VEN_9005&DEV_0250&SUBSYS_028C1014,PCI\VEN_9005&DEV_0250&SUBSYS_028E1014"
ms_1_isBusExtender	= false
ms_1_exc_replaceIfOS= "w2k3"
ms_1_exc_skipIfOS= "w2k,wxp"

[I-4]
ms_count 			= 1
ms_1_deviceName		= "IBM ServeRAID 8i 8k 8k-l Adapters (Windows 2000/XP 32-bit)"
ms_1_tag			= "aacsas"
ms_1_sysFile		= "aacsas.sys"
ms_1_hwids			= "PCI\VEN_9005&DEV_0285&SUBSYS_02f21014,PCI\VEN_9005&DEV_0286&SUBSYS_95801014,PCI\VEN_9005&DEV_0285&SUBSYS_034D1014,PCI\VEN_9005&DEV_0286&SUBSYS_029D9005,PCI\VEN_9005&DEV_0286&SUBSYS_029C9005,PCI\VEN_9005&DEV_0286&SUBSYS_029B9005,PCI\VEN_9005&DEV_0286&SUBSYS_02A09005,PCI\VEN_9005&DEV_0286&SUBSYS_02A69005,PCI\VEN_9005&DEV_0286&SUBSYS_02A19005,PCI\VEN_9005&DEV_0285&SUBSYS_02989005,PCI\VEN_9005&DEV_0285&SUBSYS_02999005,PCI\VEN_9005&DEV_0285&SUBSYS_029A9005,PCI\VEN_9005&DEV_0285&SUBSYS_02A49005,PCI\VEN_9005&DEV_0285&SUBSYS_02A59005,PCI\VEN_9005&DEV_0286&SUBSYS_02A29005,PCI\VEN_9005&DEV_0286&SUBSYS_02A39005,PCI\VEN_9005&DEV_0286&SUBSYS_02AC9005,PCI\VEN_9005&DEV_0286&SUBSYS_02A79005,PCI\VEN_9005&DEV_0286&SUBSYS_02A99005,PCI\VEN_9005&DEV_0286&SUBSYS_02B39005,PCI\VEN_9005&DEV_0286&SUBSYS_02B49005,PCI\VEN_9005&DEV_0286&SUBSYS_02A89005,PCI\VEN_9005&DEV_0286&SUBSYS_02AA9005,PCI\VEN_9005&DEV_0285&SUBSYS_02B59005,PCI\VEN_9005&DEV_0285&SUBSYS_02B69005,PCI\VEN_9005&DEV_0285&SUBSYS_02B79005,PCI\VEN_9005&DEV_0285&SUBSYS_02B09005,PCI\VEN_9005&DEV_0285&SUBSYS_02B515D9,PCI\VEN_9005&DEV_0285&SUBSYS_02B615D9"
ms_1_isBusExtender	= false
ms_1_exc_disableIfOS= "w2k"
ms_1_exc_skipIfOS	= "w2k3"

[I-5]
ms_count 			= 1
ms_1_deviceName		= "IBM ServeRAID 8i 8k 8k-l SAS-SATA Adapters (Windows 2003 32-bit)"
ms_1_tag			= "arcsas"
ms_1_sysFile		= "arcsas.sys"
ms_1_hwids			= "PCI\VEN_9005&DEV_0285&SUBSYS_02f21014,PCI\VEN_9005&DEV_0286&SUBSYS_95801014,PCI\VEN_9005&DEV_0285&SUBSYS_034D1014,PCI\VEN_9005&DEV_0286&SUBSYS_029D9005,PCI\VEN_9005&DEV_0286&SUBSYS_029C9005,PCI\VEN_9005&DEV_0286&SUBSYS_029B9005,PCI\VEN_9005&DEV_0286&SUBSYS_02A09005,PCI\VEN_9005&DEV_0286&SUBSYS_02A69005,PCI\VEN_9005&DEV_0286&SUBSYS_02A19005,PCI\VEN_9005&DEV_0285&SUBSYS_02989005,PCI\VEN_9005&DEV_0285&SUBSYS_02999005,PCI\VEN_9005&DEV_0285&SUBSYS_029A9005,PCI\VEN_9005&DEV_0285&SUBSYS_02A49005,PCI\VEN_9005&DEV_0285&SUBSYS_02A59005,PCI\VEN_9005&DEV_0286&SUBSYS_02A29005,PCI\VEN_9005&DEV_0286&SUBSYS_02A39005,PCI\VEN_9005&DEV_0286&SUBSYS_02AC9005,PCI\VEN_9005&DEV_0286&SUBSYS_02A79005,PCI\VEN_9005&DEV_0286&SUBSYS_02A99005,PCI\VEN_9005&DEV_0286&SUBSYS_02B39005,PCI\VEN_9005&DEV_0286&SUBSYS_02B49005,PCI\VEN_9005&DEV_0286&SUBSYS_02A89005,PCI\VEN_9005&DEV_0286&SUBSYS_02AA9005,PCI\VEN_9005&DEV_0285&SUBSYS_02B59005,PCI\VEN_9005&DEV_0285&SUBSYS_02B69005,PCI\VEN_9005&DEV_0285&SUBSYS_02B79005,PCI\VEN_9005&DEV_0285&SUBSYS_02B09005,PCI\VEN_9005&DEV_0285&SUBSYS_02B515D9,PCI\VEN_9005&DEV_0285&SUBSYS_02B615D9"
ms_1_isBusExtender	= false
ms_1_exc_skipIfOS	= "w2k,wxp"

[I-6]
ms_count 			= 1
ms_1_deviceName		= "IBM ServeRAID 8e SAS Adapters Adaptec 94xx (Windows 2000/XP/2003 32-bit)"
ms_1_tag			= "adp94xx"
ms_1_sysFile		= "adp94xx.sys"
ms_1_hwids			= "PCI\VEN_9005&DEV_0410,PCI\VEN_9005&DEV_0411,PCI\VEN_9005&DEV_0412,PCI\VEN_9005&DEV_041E,PCI\VEN_9005&DEV_041F,PCI\VEN_9005&DEV_0430,PCI\VEN_9005&DEV_0432,PCI\VEN_9005&DEV_0415,PCI\VEN_9005&DEV_0416,PCI\VEN_9005&DEV_043E,PCI\VEN_9005&DEV_043F"
ms_1_isBusExtender	= false
ms_1_exc_disableIfOS= "w2k"

Last edited by zookeeper (2007-04-19 05:11:27)

Re: [REQ] New drivers for IBM ServeRAID Adapters

Details about the new D\M\I folders

Folder D\M\I\1 contains
v7.10.18
IBM ServeRAID 4H Controller (Windows 2000/XP 32-bit)
IBM ServeRAID 3H/3L Controller  (Windows 2000/XP 32-bit)
IBM ServeRAID II Controller (Windows 2000/XP 32-bit)

Folder D\M\I\2 contains
v7.10.18
IBM ServeRAID 4M Controller (Windows 2000/XP 32-bit)
IBM ServeRAID 4L Controller (Windows 2000/XP 32-bit)
IBM ServeRAID 4Mx Controller (Windows 2000/XP 32-bit)
IBM ServeRAID 4Lx Controller (Windows 2000/XP 32-bit)
IBM ServeRAID 5i Controller (Windows 2000/XP 32-bit)
IBM ServeRAID 6M Controller (Windows 2000/XP 32-bit)
IBM ServeRAID 6i Controller (Windows 2000/XP 32-bit)
IBM ServeRAID 7k Controller (Windows 2000/XP 32-bit)

Folder D\M\I\3 contains
v7.12.11
IBM ServeRAID 4Mx Controller (Windows 2003 32-bit)
IBM ServeRAID 4Lx Controller (Windows 2003 32-bit)
IBM ServeRAID 5i Controller (Windows 2003 32-bit)
IBM ServeRAID 6M Controller (Windows 2003 32-bit)
IBM ServeRAID 6i Controller (Windows 2003 32-bit)
IBM ServeRAID 7k Controller (Windows 2003 32-bit)

Folder D\M\I\4 contains
v5.2.0.11829
IBM ServeRAID 8i Controller (Windows 2000/XP 32-bit)
IBM ServeRAID 8k/8k-l Controller (Windows 2000/XP 32-bit)
IBM ServeRAID 8s Controller (Windows 2000/XP 32-bit)
Adaptec SAS/SATA-II RAID Controller (Windows 2000/XP 32-bit)
Adaptec SATA RAID AAR-2420SA Controller (Windows 2000/XP 32-bit)
Adaptec SATA RAID AAR-2620SA Controller (Windows 2000/XP 32-bit)
Adaptec SATA RAID AAR-2820SA Controller (Windows 2000/XP 32-bit)
ICP SATA RAID ICP9047MA Controller (Windows 2000/XP 32-bit)
ICP SATA RAID ICP9067MA Controller (Windows 2000/XP 32-bit)
ICP SATA RAID ICP9087MA Controller (Windows 2000/XP 32-bit)
Adaptec RAID 4000 (Windows 2000/XP 32-bit)
Adaptec SAS RAID 4800SAS Controller (Windows 2000/XP 32-bit)
Adaptec SAS RAID 4805SAS Controller (Windows 2000/XP 32-bit)
ICP SAS RAID ICP9085LI Controller (Windows 2000/XP 32-bit)
ICP SAS RAID ICP5085BR Controller (Windows 2000/XP 32-bit)
Adaptec RAID 3800 (Windows 2000/XP 32-bit)
ICP SAS RAID ICP5445AU Controller (Windows 2000/XP 32-bit)
Adaptec RAID 1800 (Windows 2000/XP 32-bit)
Adaptec RAID 3805 (Windows 2000/XP 32-bit)
ICP SAS RAID ICP5085AU Controller (Windows 2000/XP 32-bit)
Adaptec RAID 2400 (Windows 2000/XP 32-bit)
ICP SAS RAID ICP5045AL Controller (Windows 2000/XP 32-bit)
Adaptec RAID 3400 (Windows 2000/XP 32-bit)
ICP SAS RAID ICP5045AU Controller (Windows 2000/XP 32-bit)
Adaptec RAID 5800 (Windows 2000/XP 32-bit)
Adaptec RAID 5805 (Windows 2000/XP 32-bit)
Adaptec RAID 5808 (Windows 2000/XP 32-bit)
Adaptec RAID ARK-1000/8 Controller (Windows 2000/XP 32-bit)
AOC-USAS1-I8i RAID Controller (Windows 2000/XP 32-bit)
AOC-USAS1-I4i RAID Controller (Windows 2000/XP 32-bit)
Adaptec SAS/SATA-II RAID Miniport Driver (Windows 2000/XP 32-bit)

Folder D\M\I\5 contains
v5.2.0.11829
IBM ServeRAID 8i Controller (Windows 2003 32-bit)
IBM ServeRAID 8k/8k-l Controller (Windows 2003 32-bit)
IBM ServeRAID 8s Controller (Windows 2003 32-bit)
Adaptec SAS/SATA-II RAID Controller (Windows 2003 32-bit)
Adaptec SATA RAID AAR-2420SA Controller (Windows 2003 32-bit)
Adaptec SATA RAID AAR-2620SA Controller (Windows 2003 32-bit)
Adaptec SATA RAID AAR-2820SA Controller (Windows 2003 32-bit)
ICP SATA RAID ICP9047MA Controller (Windows 2003 32-bit)
ICP SATA RAID ICP9067MA Controller (Windows 2003 32-bit)
ICP SATA RAID ICP9087MA Controller (Windows 2003 32-bit)
Adaptec RAID 4000 (Windows 2003 32-bit)
Adaptec SAS RAID 4800SAS Controller (Windows 2003 32-bit)
Adaptec SAS RAID 4805SAS Controller (Windows 2003 32-bit)
ICP SAS RAID ICP9085LI Controller (Windows 2003 32-bit)
ICP SAS RAID ICP5085BR Controller (Windows 2003 32-bit)
Adaptec RAID 3800 (Windows 2003 32-bit)
ICP SAS RAID ICP5445AU Controller (Windows 2003 32-bit)
Adaptec RAID 1800 (Windows 2003 32-bit)
Adaptec RAID 3805 (Windows 2003 32-bit)
ICP SAS RAID ICP5085AU Controller (Windows 2003 32-bit)
Adaptec RAID 2400 (Windows 2003 32-bit)
ICP SAS RAID ICP5045AL Controller (Windows 2003 32-bit)
Adaptec RAID 3400 (Windows 2003 32-bit)
ICP SAS RAID ICP5045AU Controller (Windows 2003 32-bit)
Adaptec RAID 5800 (Windows 2003 32-bit)
Adaptec RAID 5805 (Windows 2003 32-bit)
Adaptec RAID 5808 (Windows 2003 32-bit)
Adaptec RAID ARK-1000/8 Controller (Windows 2003 32-bit)
AOC-USAS1-I8i RAID Controller (Windows 2003 32-bit)
AOC-USAS1-I4i RAID Controller (Windows 2003 32-bit)
Adaptec SAS/SATA-II RAID Miniport Driver (Windows 2003 32-bit)

Folder D\M\I\6 contains
v1.2.5929.0 06/28/2006
IBM ServeRAID 8e SAS/SATA Adapter (Windows 2000/XP/2003 32-bit)
Adaptec ASC-48300 SAS/SATA Host Adapter (Windows 2000/XP/2003 32-bit)
Adaptec COMSTOCK SAS/SATA Controller (Windows 2000/XP/2003 32-bit)
Adaptec ASC-48300 SAS/SATA Host Adapter (Windows 2000/XP/2003 32-bit)
Adaptec AIC-9410w SAS/SATA Controller (Windows 2000/XP/2003 32-bit)
Adaptec AIC-9410w SAS/SATA Controller (Windows 2000/XP/2003 32-bit)
Adaptec ASC-44300 SAS/SATA Controller (Windows 2000/XP/2003 32-bit)
Adaptec ASC-44300 SAS/SATA Controller (Windows 2000/XP/2003 32-bit)
Adaptec ASC-58300 SAS/SATA Controller (Windows 2000/XP/2003 32-bit)
Adaptec ASC-58300 SAS/SATA Controller (Windows 2000/XP/2003 32-bit)
Adaptec AIC-9405 SAS/SATA Controller (Windows 2000/XP/2003 32-bit)
Adaptec AIC-9405 SAS/SATA Controller (Windows 2000/XP/2003 32-bit)

Last edited by zookeeper (2007-04-18 03:08:57)

Re: [REQ] New drivers for IBM ServeRAID Adapters

Thats funny, I'm testing Adaptec ICP RAID controllers ICP9024RO and ICP5085LI just now, so I had updated [AD-2] in my own copy.
I downloaded the XP version from here:
http://www.adaptec.com/en-US/downloads/ … +ICP9085LI
It seems to be the same as your Folder D\M\I\4 v5.2.0.11829, but the Adaptec download is some older and is not signed.

I've also updated my *.ini as follows:

[AD-2]
ms_count 			= 2
ms_1_deviceName		= "Adaptec SATA/SCSI RAID Controllers"
ms_1_tag			= "aac"
ms_1_sysFile		= "aac.sys"
ms_1_hwids			= "PCI\VEN_9005&DEV_0285&SUBSYS_02859005,PCI\VEN_9005&DEV_0285&SUBSYS_02879005,PCI\VEN_9005&DEV_0285&SUBSYS_02869005,PCI\VEN_9005&DEV_0285&SUBSYS_028A9005,PCI\VEN_9005&DEV_0285&SUBSYS_028E9005,PCI\VEN_9005&DEV_0285&SUBSYS_028B9005,PCI\VEN_9005&DEV_0285&SUBSYS_028F9005,PCI\VEN_9005&DEV_0285&SUBSYS_02909005,PCI\VEN_9005&DEV_0285&SUBSYS_02929005,PCI\VEN_9005&DEV_0285&SUBSYS_02939005,PCI\VEN_9005&DEV_0285&SUBSYS_3227103C,PCI\VEN_9005&DEV_0286&SUBSYS_028C9005,PCI\VEN_9005&DEV_0286&SUBSYS_028D9005,PCI\VEN_9005&DEV_0286&SUBSYS_029E9005,PCI\VEN_9005&DEV_0286&SUBSYS_029F9005"
ms_1_isBusExtender	= false
ms_2_deviceName		= "Adaptec SAS RAID Controllers"
ms_2_tag			= "aacsas"
ms_2_sysFile		= "aacsas.sys"
ms_2_hwids			= "PCI\VEN_9005&DEV_0285&SUBSYS_02f21014,PCI\VEN_9005&DEV_0286&SUBSYS_95801014,PCI\VEN_9005&DEV_0286&SUBSYS_029D9005,PCI\VEN_9005&DEV_0286&SUBSYS_029C9005,PCI\VEN_9005&DEV_0286&SUBSYS_029B9005,PCI\VEN_9005&DEV_0286&SUBSYS_02A09005,PCI\VEN_9005&DEV_0286&SUBSYS_02A69005,PCI\VEN_9005&DEV_0286&SUBSYS_02A19005,PCI\VEN_9005&DEV_0285&SUBSYS_02989005,PCI\VEN_9005&DEV_0285&SUBSYS_02999005,PCI\VEN_9005&DEV_0285&SUBSYS_029A9005,PCI\VEN_9005&DEV_0285&SUBSYS_02A49005,PCI\VEN_9005&DEV_0285&SUBSYS_02A59005,PCI\VEN_9005&DEV_0285&SUBSYS_034D1014,PCI\VEN_9005&DEV_0286&SUBSYS_02A29005,PCI\VEN_9005&DEV_0286&SUBSYS_02A39005,PCI\VEN_9005&DEV_0286&SUBSYS_02AC9005,PCI\VEN_9005&DEV_0286&SUBSYS_02A79005,PCI\VEN_9005&DEV_0286&SUBSYS_02A99005,PCI\VEN_9005&DEV_0286&SUBSYS_02B39005,PCI\VEN_9005&DEV_0286&SUBSYS_02B49005,PCI\VEN_9005&DEV_0286&SUBSYS_02A89005,PCI\VEN_9005&DEV_0286&SUBSYS_02AA9005,PCI\VEN_9005&DEV_0285&SUBSYS_02B59005,PCI\VEN_9005&DEV_0285&SUBSYS_02B69005,PCI\VEN_9005&DEV_0285&SUBSYS_02B79005"
ms_2_isBusExtender	= false

So I think this time we can bring them together, since the IBM drivers contain all IDs the Adaptec ICP files also contain as far I can see.

Re: [REQ] New drivers for IBM ServeRAID Adapters

i would NOT do that the ini is not done correctly

[I-1]
ms_count             = 1
ms_1_deviceName        = "IBM ipsraidn ServeRAID Adapters (Windows 2000/XP 32-bit)"
ms_1_tag            = "ipsraidn"
ms_1_sysFile        = "ipsraidn.sys"
ms_1_hwids            = "PCI\VEN_1014&DEV_002E&SUBSYS_022E1014&REV_10,PCI\VEN_1014&DEV_002E&SUBSYS_002E1014&REV_0D,PCI\VEN_1014&DEV_002E&SUBSYS_00000000&REV_04,PCI\VEN_1014&DEV_002E&SUBSYS_00000000&REV_03,PCI\VEN_1014&DEV_002E&SUBSYS_00000000&REV_02"
ms_1_isBusExtender    = false
ms_1_exc_disableIfOS= "w2k"
ms_1_exc_replaceIfOS= "w2k,wxp"
ms_1_exc_skipIfOS= "W2k3"

That Is wrong.... replaceIfOS= "w2k,wxp" 
implies that ipsraidn.sys exists in a native w2k or XP install and must be backed up removed and overwritten. it is not natively supported in either and is not a replacement. 

This may seem a small detail but it will totaly blow up the slipstream of driverpacks base. It affects which entries in which files get changed during the slipstream process. Skip does mean don't use at all, as you thought. You also did not indicate that you had properly groomed your files before making the folders.

There is actually a long list of things wrong but I dont want to seem to be flaming you.

So

1) all of your ini's are done incorrectly and although may work on your OS and PC will not work as intended (on ANY OS / machine)

2) your files are probably not technicaly "ready" for the pack (but probably work). 
Please add [REQ] in front your first post title and well do it correctly for you!

I would REALLY REALLY REALLY like to thank you for being so thorough and spending so much time putting this together. very nice documentation of what you did. (other than the fact it is trashed i like it)

Perhaps you would like to join the team and we can assist you with adding and testing drivers.
Muiz (Leader of the Packs- hee hee) is always looking for motivated people who can document thier work.


These two have a second thread running here too

also please read jaaks post at the below link and understand more of what im not trashing him about!
http://forum.driverpacks.net/viewtopic. … 029#p10029

Last edited by OverFlow (2007-04-18 18:18:33)

DP BartPE Tutorial   DP_BASE Tutorial   HWID's Tool     Read BEFORE you post    UserBars!
http://driverpacks.net/userbar/admin-1.png
The DriverPacks, the DP_Base program, and Support Forum are FREE!.

Re: [REQ] New drivers for IBM ServeRAID Adapters

1) It is unfortunate that the ini files are thrash.  I would really like to see them done correctly so that we can all learn from the mistakes. More importantly, we need to keep it working smile

2) I added [REQ] to the topic title.

I would like to join the team. In addition to Mass Storage drivers, I also have more drivers for graphics, sound and security chipsets. Also have enhancements for DpsFnshr.exe. How do I become a member?

Thanks for the thanks.

Re: [REQ] New drivers for IBM ServeRAID Adapters

Hi zookeeper.
you waited long enough, the files finally got looked at again.

The answer was 42?
Kind regards, Jaak.

Re: [REQ] New drivers for IBM ServeRAID Adapters

at bottom of this http://forum.driverpacks.net/viewtopic.php?id=1637

The answer was 42?
Kind regards, Jaak.

Re: [REQ] New drivers for IBM ServeRAID Adapters

@jtdoom

Hi jtdoom,

Like a great bottle of wine, sometimes you have to wait for perfection.
Thanks for revisiting and updating the driver pack with the newer version of the IBM drivers.

Re: [REQ] New drivers for IBM ServeRAID Adapters

ditto.

In HWIDs?
bring sushi or dumplings <<  How Wonderful Industrial Documents suck.
Vote.

The answer was 42?
Kind regards, Jaak.