Topic: Blue screen in xp installation

I’ve added Mass Storage driver pack in my XP CD successfully following this post and I used it in many laptops (HP, Dell, Acer, Toshiba, Compaq) without any problems. But Sony VAIO Laptop shows blue screen immediately before F8= I agree page. It’s BIOS is very simple and nothing to configure HDD for AHCI. Any suggestion please?

Last edited by Kamrul08 (2013-04-19 21:08:03)

Re: Blue screen in xp installation

try a different version of mass storage... either older or the release candidate that is floating around in the mass storage forum. *you are here

DP BartPE Tutorial   DP_BASE Tutorial   HWID's Tool     Read BEFORE you post    UserBars!
http://driverpacks.net/userbar/admin-1.png
The DriverPacks, the DP_Base program, and Support Forum are FREE!.

Re: Blue screen in xp installation

OverFlow wrote:

try a different version of mass storage... either older or the release candidate that is floating around in the mass storage forum. *you are here

Thanks OverFlow. I used Mass Storage Pack 11.04. I think Mass Storage drivers are not working here. Because Mass Storage works after second session of XP installation. But this problem shows before second session (just before C drive). Blue screen appears during the installation detecting HDD. I think XP is not getting proper drivers. My HDD is OK. Win 7 installation works fine. I tried resizing, Splitting my C drive also.

Re: Blue screen in xp installation

Try the RC... http://forum.driverpacks.net/viewtopic.php?id=6622

Mass storage does work at the first stage of setup as well as the second wink

DP BartPE Tutorial   DP_BASE Tutorial   HWID's Tool     Read BEFORE you post    UserBars!
http://driverpacks.net/userbar/admin-1.png
The DriverPacks, the DP_Base program, and Support Forum are FREE!.

Re: Blue screen in xp installation

Don't forget to clear your DP_BASE "QSC Cache", better yet, disable it unless you are doing multiple integrations.
Also, ensure that you use the RC for Chipset & the beta for Misc if applicable.

If you are still experiencing problems with the RC, please post your HWID's with the tool linked in either of our signatures.

Last edited by TechDud (2013-04-12 18:07:01)

Re: Blue screen in xp installation

Thanks OverFlow & TechDud. I'll apply your instructions and write feedback.

Re: Blue screen in xp installation

Sorry for late.
I tried disable "QSC Cache" option during adding Mass Storage with DPs_BASE. Now no blue screen but PC shutdown fully appearing HDD drives a while. I tried with Chipset and without Chipset.
My machine is SVE14125YCW

Re: Blue screen in xp installation

Delete QSC Cache in DP_BASE folder.  Then integrate from source.

Use WinSetupFromUSB_1beta8 to make USB Flash Disk.
  Replace the included DPMS.iso from same page as the RC.     smile

  If flash disk fails, burn dvd.
Report your results, including MassStorage HWID's, please.

Last edited by TechDud (2013-04-17 15:03:56)

Re: Blue screen in xp installation

I tried with DP_Chipset_wnt5_x86-32_1209.7z and DP_MassStorage_wnt5_x86-32_1304r2.7z. I disabled "QSC Cache". So QSC folder is not created and nothing found as QSC Cache. I don’t know how to use MassStorage.iso. So I’m not trying USB. On the other hand I’ve CD-RW and no problem with CD.
My PC is running windows 7 now and I ran SaveHwids.exe in win7. My HWID's.

Re: Blue screen in xp installation

You should use DP_Chipset_wnt5_x86-32_1304r2 with DP_MassStorage_wnt5_x86-32_1304r2, not the earlier one.

Out-of-date or otherwise incompatible BIOS &/or uEFI can at times be a possible source of such issues.  BIOS Updates carry inherent risks.  Know what you are doing, or don't start.  A "Bricked" System Board (or other) could result.  Downgrades possible alternative.

Good to hear that NT6.1 is working out for you.  Thank you for the reports.
Is there another version of intel's RST that worked for you, previously?

Last edited by TechDud (2013-04-18 18:13:28)

Re: Blue screen in xp installation

Thanks TechDud for your great instructions.
I followed your advices and tried again but still same problem (suddenly shutting down appearing HDD drives). I didn't face this problem before. I used previous version of Chipset and Mass Storage in my previous CD and used in HP, Dell, Acer, Toshiba, Compaq brand without problem. I added two screen shots about driver integration.

Adding Mass Storage,

disabled QSC Cache

Re: Blue screen in xp installation

First off, i note that there is only one MassStorage Controller in that Sony:

=========== 
PCI Devices 
=========== 
PCI\VEN_168C&DEV_0032&SUBSYS_E044105B&REV_01\4&80CAA06&0&00E0: Network Controller
PCI\VEN_8086&DEV_1E22&SUBSYS_90AB104D&REV_04\3&11583659&1&FB: Synaptics SMBus Driver
PCI\VEN_8086&DEV_0154&SUBSYS_90AB104D&REV_09\3&11583659&1&00: 3rd Gen Core processor DRAM Controller - 0154
PCI\VEN_8086&DEV_1E26&SUBSYS_90AB104D&REV_04\3&11583659&1&E8: Intel(R) 7 Series/C216 Chipset Family USB Enhanced Host Controller - 1E26
PCI\VEN_8086&DEV_0166&SUBSYS_90AB104D&REV_09\3&11583659&1&10: Intel(R) HD Graphics 4000
PCI\VEN_8086&DEV_1E2D&SUBSYS_90AB104D&REV_04\3&11583659&1&D0: Intel(R) 7 Series/C216 Chipset Family USB Enhanced Host Controller - 1E2D
PCI\VEN_8086&DEV_1E03&SUBSYS_90AB104D&REV_04\3&11583659&1&FA: Intel(R) 7 Series Chipset Family SATA AHCI Controller
PCI\VEN_8086&DEV_1E31&SUBSYS_90AB104D&REV_04\3&11583659&1&A0: Intel(R) USB 3.0 eXtensible Host Controller
PCI\VEN_8086&DEV_1E10&SUBSYS_90AB104D&REV_C4\3&11583659&1&E0: Intel(R) 7 Series/C216 Chipset Family PCI Express Root Port 1 - 1E10
PCI\VEN_8086&DEV_1E3A&SUBSYS_90AB104D&REV_04\3&11583659&1&B0: Intel(R) Management Engine Interface 
PCI\VEN_8086&DEV_1E12&SUBSYS_90AB104D&REV_C4\3&11583659&1&E1: Intel(R) 7 Series/C216 Chipset Family PCI Express Root Port 2 - 1E12
PCI\VEN_8086&DEV_1E59&SUBSYS_90AB104D&REV_04\3&11583659&1&F8: Intel(R) HM76 Express Chipset LPC Controller - 1E59
PCI\VEN_8086&DEV_1E14&SUBSYS_90AB104D&REV_C4\3&11583659&1&E2: Intel(R) 7 Series/C216 Chipset Family PCI Express Root Port 3 - 1E14
PCI\VEN_10EC&DEV_8168&SUBSYS_90AB104D&REV_07\4&360D8B31&0&00E2: Realtek PCIe GBE Family Controller
PCI\VEN_8086&DEV_1E20&SUBSYS_90AB104D&REV_04\3&11583659&1&D8: High Definition Audio Controller
15 matching device(s) found.
 
=========== 
USB Devices 
=========== 
USB\VID_05CA&PID_18C3&MI_00\7&35BE23CD&0&0000               : USB2.0 Camera
USB\VID_8087&PID_0024\5&24FC3825&0&1                        : Generic USB Hub
USBSTOR\DISK&VEN_USB&PROD_FLASH_DRIVE&REV_3000\H410050400000073&0: USB FLASH DRIVE USB Device
USB\VID_8087&PID_0024\5&659EAFB&0&1                         : Generic USB Hub
USB\VID_15D9&PID_0A4C\6&F320AE7&0&4                         : USB Input Device
USB\VID_1005&PID_B113\H410050400000073                      : USB Mass Storage Device
USB\ROOT_HUB20\4&1501D67&0                                  : USB Root Hub
USB\VID_05CA&PID_18C3\6&1DECD1&0&3                          : USB Composite Device
USB\ROOT_HUB20\4&3BC5FDF&0                                  : USB Root Hub
9 matching device(s) found.
 
============= 
Input Devices 
============= 
HID\VID_15D9&PID_0A4C\7&A1B8D63&0&0000                      : HID-compliant mouse
1 matching device(s) found.
 
============ 
ACPI Devices 
============ 
ACPI\SNY5001\4&ABEBC9D&0                                    : Sony Firmware Extension Parser Device
ACPI\SYN2704\4&ABEBC9D&0                                    : Synaptics PS/2 Port Compatible TouchPad
ROOT\ACPI_HAL\0000                                          : ACPI x86-based PC
ACPI\THERMALZONE\THRM                                       : ACPI Thermal Zone
ACPI\INT0800\4&ABEBC9D&0                                    : Intel(R) 82802 Firmware Hub Device
ACPI_HAL\PNP0C08\0                                          : Microsoft ACPI-Compliant System
ACPI\INT340E\2&DABA3FF&2                                    : Motherboard resources
ACPI_HAL\PNP0C18\0                                          : Microsoft Watchdog Timer
ACPI\INT3F0D\4&ABEBC9D&0                                    : Motherboard resources
ACPI\ACPI0003\2&DABA3FF&2                                   : Microsoft AC Adapter
ACPI\PNP0000\4&ABEBC9D&0                                    : Programmable interrupt controller
ACPI\FIXEDBUTTON\2&DABA3FF&2                                : ACPI Fixed Feature Button
ACPI\PNP0100\4&ABEBC9D&0                                    : System timer
ACPI\GENUINEINTEL_-_X86_FAMILY_6_MODEL_58_-________INTEL(R)_CORE(TM)[email protected]_2.40GHZ\_1: Intel(R) Core(TM) i3-3110M CPU @ 2.40GHz
ACPI\PNP0103\0                                              : High Precision Event Timer
ACPI\PNP0200\4&ABEBC9D&0                                    : Direct memory access controller
ACPI\PNP0303\4&ABEBC9D&0                                    : Standard 101/102-Key or Microsoft Natural PS/2 Keyboard with HP QLB
ACPI\PNP0A08\0                                              : PCI bus
ACPI\GENUINEINTEL_-_X86_FAMILY_6_MODEL_58_-________INTEL(R)_CORE(TM)[email protected]_2.40GHZ\_2: Intel(R) Core(TM) i3-3110M CPU @ 2.40GHz
ACPI\PNP0B00\4&ABEBC9D&0                                    : System CMOS/real time clock
ACPI\PNP0C01\2                                              : System board
ACPI\PNP0C02\1                                              : Motherboard resources
ACPI\PNP0C02\2                                              : Motherboard resources
ACPI\PNP0C04\4&ABEBC9D&0                                    : Numeric data processor
ACPI\GENUINEINTEL_-_X86_FAMILY_6_MODEL_58_-________INTEL(R)_CORE(TM)[email protected]_2.40GHZ\_3: Intel(R) Core(TM) i3-3110M CPU @ 2.40GHz
ACPI\PNP0C09\4&ABEBC9D&0                                    : Microsoft ACPI-Compliant Embedded Controller
ACPI\PNP0C0A\1                                              : Microsoft ACPI-Compliant Control Method Battery
ACPI\PNP0C0C\2&DABA3FF&2                                    : ACPI Power Button
ACPI\GENUINEINTEL_-_X86_FAMILY_6_MODEL_58_-________INTEL(R)_CORE(TM)[email protected]_2.40GHZ\_4: Intel(R) Core(TM) i3-3110M CPU @ 2.40GHz
ACPI\PNP0C0D\2&DABA3FF&2                                    : ACPI Lid
30 matching device(s) found.
 
============ 
 HDA Audio 
============ 
HDAUDIO\FUNC_01&VEN_10EC&DEV_0269&SUBSYS_104D6900&REV_1002\4&293A596C&0&0001: High Definition Audio Device
HDAUDIO\FUNC_01&VEN_8086&DEV_2806&SUBSYS_104D6900&REV_1000\4&293A596C&0&0301: Intel(R) Display Audio
2 matching device(s) found.
 
============ 
RAID Devices 
============ 
PCI\VEN_8086&DEV_1E03&SUBSYS_90AB104D&REV_04\3&11583659&1&FA
    Name: Intel(R) 7 Series Chipset Family SATA AHCI Controller
    Hardware ID's:
        PCI\VEN_8086&DEV_1E03&SUBSYS_90AB104D&REV_04
        PCI\VEN_8086&DEV_1E03&SUBSYS_90AB104D
        PCI\VEN_8086&DEV_1E03&CC_010601
        PCI\VEN_8086&DEV_1E03&CC_0106
    Compatible ID's:
        PCI\VEN_8086&DEV_1E03&REV_04
        PCI\VEN_8086&DEV_1E03
        PCI\VEN_8086&CC_010601
        PCI\VEN_8086&CC_0106
        PCI\VEN_8086
        PCI\CC_010601
        PCI\CC_0106
1 matching device(s) found.

If you are installing from a dvd drive on that controller, it would probably not work.
If it is the Intel USB 3.0 controller, ensure that USB 2.0 mode is selected in BIOS/uEFI.
It should be the "Intel(R) 7 Series/C216 Chipset Family USB Enhanced Host Controller - 1E26" that would have the best odds of success.
Only plug in a bare minimum of accessories, such as the USB-CD/DVD (no hubs, cardreaders, etc.).

Otherwise, i would remind you of BIOS/uEFI updates/oROMs as a likely source of err, and to remind of the risks.
{I am working on a Dell XPS that stopped installing from USB (using WinSetupFromUSB v1beta8 & udpated DPMS.iso) without a bluescreen with an updated BIOS (confirmation in progress).}

edit:  it wasn't the BIOS that failed with the aforementioned Dell XPS Gen 4, it may be the choice of textmode driver.  The error is STOP:0x0000007B (0xF89C3524,0xC0000034,0,0).  The important part is that a disc-based install works there, in AHCI mode, i hope it is similar with Kamrul08's installs.  More on this in another topic, later.

I still think that a disc install has the best odds of success on the "USB Enhanced Host Controller - 1E26" without touching the BIOS/uEFI.

What are the details of your bluescreen error?

Last edited by TechDud (2013-04-19 18:59:44)

Re: Blue screen in xp installation

Just want to clarify, have you been using a clean, unmodified, XP source for your integrations?

Re: Blue screen in xp installation

This machine has three USB 2.0 Ports and one USB 3.0 Port. I only connect charger to this machine during setup and use USB 2.0 port. It's BIOS is very simple and nothing to edit without date & time, BIOS password, booting order of devices and Default Changes. I don't dare update BIOS.

As your instructions, I tried with USB using "WinSetupFromUSB Ver.0-2-3 and 1beta8". I used DP_Chipset11.11 and DP_MassStorage11.11, DP_Chipset12.09 and DP_MassStorage12.09, DP_Chipset_wnt5_x86-32_1209.7z and DP_MassStorage_wnt5_x86-32_1304r2.7z. I tried both disabled and enabled "QSC Cache". My CD and USB give me same result.

1. DP_Chipset11.11 and DP_MassStorage11.11 shows BSOD.
2. Another two version cause shutting down PC suddenly.

I didn't use DriverPack MassStorage.iso. Because I don't know how to use it.

Last edited by Kamrul08 (2013-04-19 22:08:49)

Re: Blue screen in xp installation

AC Charger good!

At this present time, i reccomend only using DP_MassStorage_wnt5_x86-32_1304r2.7z with DP_Chipset_wnt5_x86-32_1304r2.7z.

Also, did you heed Damnation's warning about using an unmodified source?

Which driver version does Sony recommend for XP or Win2k3 installation?
Please provide a link.

Last edited by TechDud (2013-04-19 23:23:53)

Re: Blue screen in xp installation

I didn't get any warning. I couldn't find any driver version any where. This model is very rare in online. Even I couldn't find this model in Sony site. I found a link in Chinese language. Here is Google Translated link. This machine is bought from Singapore and it's my friend PC.

Thanks TechDud for help. I've give up XP in this PC. So let the post finish. Thanks again for your helpful advices. I love this site very much for driver.

Re: Blue screen in xp installation

"I didn't get any warning."

I understand how that can happen, forums are not the most natural way of communicating.

Damnation wrote:

"Just want to clarify, have you been using a clean, unmodified, XP source for your integrations?"

He's quite right.  It has been known to happen.  A copy of all the setup files from a NT5 disc oft copied onto a hard drive which is rewritable media.  It's one reason that i take extra time to verify hashes, to prevent inadvertent mistakes!

http://service.sony.com.cn/vaio/SVE14115YCW.htm
No luck with drivers, nor a official BIOS update.

India's support has been kind, and indicates that other listed models in the SVE1411* series use Intel's RST v     11.1.0.1006 {DriverVer=02/01/2012,11.1.0.1006}.  No BIOS, though.
    http://www.sony-asia.com/support/product/sve14115fg

  Lenovo seems to advise the initial release for some models {DriverVer=11/29/2011,11.0.0.1032}.  That may be the one you ultimately need.

Is that a CoreBoot BIOS?
  If not, have you access to a USB-Floppy drive and that unmodified XP disc? 

Quote from Intel(R)'s readme.txt within RST v11.1:

"5.3 Pre-Installation Using the F6 Method. 

Note: The Steps 1 and 2 can be skipped if you use the F6 Floppy
      disk utility provided by Intel. These methods 
      are applicable to systems configured for RAID or 
      AHCI mode.

1.  Extract all driver files from the installation package.
    See section 7.2 for instructions on extracting the 
    files.

2.  Create a floppy* containing the following files in the root 
    directory:
    iaAhci.inf, iaAhci.cat,
    iaStor.inf, iaStor.cat,
    iaStor.sys, and 
    TxtSetup.oem. 

    * Note: For Windows* Vista, you can use a floppy, CD/DVD or USB.

3.  For Microsoft Windows* XP:

    - At the beginning of the operating system installation,
     press F6 to install a third party SCSI or RAID driver.

    - When prompted, select 'S' to Specify Additional Device.

    - Continue to step 5."

v11.0 - http://downloadmirror.intel.com/20868/e … 0.1032.zip
v11.1 - http://download.gigabyte.us/FileList/Dr … series.exe


There you have it.  One of the two v11.0 or v11.1 drivers should work to install NT5 on that AHCI controller.
One caveat; the HWID's are not all listed for the existing USB-Floppy drives.

add to TXTSETUP.SIF after line:
USB\VID_55AA&PID_1234 = "usbstor"

these:

USB\VID_03F0&PID_2001 = "usbstor"
USB\VID_054C&PID_002C = "usbstor"
USB\VID_057B&PID_0001 = "usbstor"
USB\VID_0409&PID_0040 = "usbstor"
USB\VID_0424&PID_0FDC = "usbstor"
USB\VID_08BD&PID_1100 = "usbstor"
USB\VID_055D&PID_2020 = "usbstor"

I wish that that could be done within DP_MassStorage, yet.....I don't know how!  smile

Now you have all you should need (providing you have a USB-Floppy drive or HP USB-Floppy Flash Key) to have a fighting chance at this.

Last edited by TechDud (2013-04-20 13:41:41)

Re: Blue screen in xp installation

I used clean source of XP CD and Drive packs every times. I passed two days fully with this machine following your advices. Thanks for Floppy drivers but no way for USB floppy drive.

OK TechDud. Let the post finish. I hope you will add the matter in your next driver Packs update. I'll try next update version. I'm very grateful to you and this forum. Thanks a lot.

Re: Blue screen in xp installation

I will provide a test pack soon.  Thank you for your patience.

Last edited by TechDud (2013-04-21 17:31:35)

Re: Blue screen in xp installation

TechDud wrote:

I will provide a test pack soon.  Thank you for your patience.

OK TechDud. Thanks.

Re: Blue screen in xp installation

Here are my latest nightlies.  There's an updated set of drivers for VMWARE (from the NT6 packs), some more Ricoh Cardreader drivers for Sonys, some legacy junk, and now some x10 support.
  Also included is Intel's RST v11.0 for PCI\VEN_8086&DEV_1E02 & 1E03 to hopefully, finally be able to use textmode with either HWID.  Also moved is PCI\VEN_8086&DEV_2824 to v10.1 in [I9].

Try USB install & CD/DVD-disc install to be sure.

DP_Chipset_wnt5_x86-32_1304191.7z   
DP_MassStorage_wnt5_x86-32_1304211.7z
DP_Misc_wnt5_x86-32_1304192.7z

Chenall's_DPMS_1304211.7z

edit:  links removed - updated in latest [Nightlies]

I note that it would seem that Chenall's D-P-M-S solution is aimed at images that have not previously integrated DriverPacks.
One might dispense with the D-P-M-S option in the Advanced menu of WinSetupFromUSB if DriverPacks are already integrated.

If this doesn't work, there is only one other driver to try (v11.1).
Have you seen either HWID on any of those other machines you previously mentioned, Kamrul08?

Last edited by TechDud (2014-12-10 19:37:19)

Re: Blue screen in xp installation

Thanks TechDud. You are really great.

TechDud wrote:

One might dispense with the D-P-M-S option in the Advanced menu of WinSetupFromUSB if DriverPacks are already integrated.


There is D-P-M-S.ISO file already placed in WinSetupFromUSB 1_0_beta8\files\D-P-M-S folder and it's size 46MB. Should I replace with your new one (Chenall's_DPMS_1304211.7z)


TechDud wrote:

Have you seen either HWID on any of those other machines you previously mentioned, Kamrul08?

Actually I didn't research and notice HWID in my previous machines. Because those machines worked fine. Even I used chipset 11.11 and Mass Storage driver packs 11.04. I also integrated sound A,B (Ver_11.08), graphics (Ver_11.07), lan, cpu in my DVD. All worked fine. In some PC I face sound problem and it was VIA HD driver. MY XP was SP3.

I'll apply your driver packs soon and inform you here.

Re: Blue screen in xp installation

When WinSetupFromUSB has succeeded for me on an AHCI or RAID controller, i only needed execute first setup, then second part of setup, without using D-PMS.iso.  I think that's meant for images without the packs already integrated.  I am going to leave further mods of that to Chennal.

Last edited by TechDud (2013-04-23 17:45:41)

Re: Blue screen in xp installation

Very nice. It worked. Thanks TechDud.
How can I update this driverpacks in my already made XP CD?

Re: Blue screen in xp installation

What is it that did work?  Was Setup run from disc or USB?

As for updating your Setup disc, it is possible to use DP_BASE for this, providing that nLite has not been used previously.

It is best to start with a clean, unmodified source.  Add Updates with RVMi (not nLite as it can corrupt your source).
Also, avoid the use of OnePiece's Updates; the current update pack has problem registering rundll32 (iirc).
Use DP_BASE to integrate the DriverPacks.  Use SAD3 to install drivers after Windows Setup finishes (WLAN, HID, Webcam).

  I think that you are great for your patience and perseverance.
You will be credited in the changelog for your assistance.  Thank you again.

Last edited by TechDud (2013-04-26 16:58:20)