You are not logged in. Please login or register.
DriverPacks.net Forum » DriverPack Mass Storage » [SOLVED] JMicron JMB36X + AsRock DualSata2 + DriverPack MassStorage 7.0.1.1 = BSOD
As the title says, i've got BSOD on 1st reboot with that configuration.
I have to add this line to avoid BSOD:
PCI\VEN_197B&DEV_2360&SUBSYS_03601849&REV_02="jahci"
regards
More info please..
When i install DriverPack (Base 7.0.1.5 + Massstorage 7.0.1.1), [HardwareIdsDatabase] in txtsetup.sif is :
PCI\VEN_197B&DEV_2360="jahci"
PCI\VEN_197B&DEV_2360&CC_0104="jraid"
PCI\VEN_197B&DEV_2361&CC_0104="jraid"
PCI\VEN_197B&DEV_2363&CC_0104="jraid"
PCI\VEN_197B&DEV_2365&CC_0104="jraid"
PCI\VEN_197B&DEV_2366&CC_0104="jraid"
PCI\VEN_197B&DEV_2360&CC_0106="jraid"
PCI\VEN_197B&DEV_2361&CC_0106="jraid"
PCI\VEN_197B&DEV_2363&CC_0106="jraid"
PCI\VEN_197B&DEV_2365&CC_0106="jraid"
PCI\VEN_197B&DEV_2366&CC_0106="jraid"
during 1st boot , i get BSOD (0x00007B).
If i add the line: (which is the hardware ID for JMicron on my Asrock DualSata2) it's booting fine
PCI\VEN_197B&DEV_2360="jahci"
PCI\VEN_197B&DEV_2360&SUBSYS_03601849&REV_02="jahci"
PCI\VEN_197B&DEV_2360&CC_0104="jraid"
PCI\VEN_197B&DEV_2361&CC_0104="jraid"
PCI\VEN_197B&DEV_2363&CC_0104="jraid"
PCI\VEN_197B&DEV_2365&CC_0104="jraid"
PCI\VEN_197B&DEV_2366&CC_0104="jraid"
PCI\VEN_197B&DEV_2360&CC_0106="jraid"
PCI\VEN_197B&DEV_2361&CC_0106="jraid"
PCI\VEN_197B&DEV_2363&CC_0106="jraid"
PCI\VEN_197B&DEV_2365&CC_0106="jraid"
PCI\VEN_197B&DEV_2366&CC_0106="jraid"
My config is : one Sata2 HD (Maxtor 6Y 200Go) and 2 dvd burners on ide ports
Can you tell us the exact model of your motherboard and specifiy where we can downloadn the jmicron drivers for your motherboard?
I would like to analyse your drivers, maybe we can add even more hardware id's.
We made a test version for you.
can you please test this one?
http://rapidshare.com/files/13612850/DP … ly.7z.html
Last edited by muiz3 (2007-01-27 23:10:49)
Thanks for the test version, i'll test it in the next hours.
About my motherboard, it's a Asrock DualSata 2/A/ASR Serial n°63M0X1012523 Part N° 90-MXG0Y0-A0UAYZ Bios version 1.9
Chipset Model ULi M1695 K8 Northbridge with PCI-Express and hypertransport
South Bridge ALI M1563 South Bridge with Hypertransport Support
About JMicron Chipset:
Property Value
Device ID PCI\VEN_197BDEV_2360SUBSYS_03601849REV_02\42FF59A8800018
Status 0x0180200a Started
Problem 0x00000000 (0)
Service JRAID
Capabilities 0x00000000
Config Flags 0x00000000
Class SCSIAdapter
Manufacturer JMicron Technology Corp.
Hardware IDs PCI\VEN_197BDEV_2360SUBSYS_03601849REV_02
PCI\VEN_197BDEV_2360SUBSYS_03601849
PCI\VEN_197BDEV_2360CC_010601
PCI\VEN_197BDEV_2360CC_0106
Compatible IDs PCI\VEN_197BDEV_2360REV_02
PCI\VEN_197BDEV_2360
PCI\VEN_197BCC_010601
PCI\VEN_197BCC_0106
PCI\VEN_197B
PCI\CC_010601
PCI\CC_0106
Class GUID {4D36E97B-E325-11CE-BFC1-08002BE10318}
Location Bus PCI 3, périphérique 0, fonction 0
Bus number 0x00000003
Enumerator name PCI
Description JMicron JMB36X Controller
Driver {4D36E97B-E325-11CE-BFC1-08002BE10318}\0001
Physical Object Name \Device\NTPNP_PCI0023
Bustype GUID {44203042-2046-4245-2043-382031302042}
Legacy bus type 0x00000005
Install State 0x00000000
Device Address 0x00000000
Device Configuration File c:\windows\inf\oem19.inf
Used Files C:\WINDOWS\system32\DRIVERS\jraid.sys
C:\WINDOWS\system32\DRIVERS\JGOGO.sys
InfPath oem19.inf
InfSection JM
ProviderName JMicron Technology Corp.
DriverDateData 00 40 7D AC 48 FD C6 01
DriverDate 11-1-2006
DriverVersion 1.17.6.4
MatchingDeviceId pci\ven_197bdev_2360subsys_03601849
DriverDesc JMicron JMB36X Controller
LegacyAdapterDetection 0
Class SCSIAdapter
Contrôleurs SCSI et RAID
Installer32 SysSetup.Dll,ScsiClassInstaller
Icon -10
LegacyInfOption SCSI
UpperFilters JGOGO
About Drivers:
Name Description Version Type Status Start Path Description
JAHCI JAHCI 5.0.1636.1 KERNEL_DRIVER Active BOOT_START C:\WINDOWS\system32\drivers\JAHCI.sys JMicron Storage Host Adapter / JMicron PCIE AHCI Controller
JGOGO JMicron Hot-Plug Driver 5.0.3790.1 KERNEL_DRIVER Active BOOT_START C:\WINDOWS\system32\drivers\JGOGO.sys SCSI Port upper filter driver
JRAID JRAID 1.17.6.3 KERNEL_DRIVER Active BOOT_START C:\WINDOWS\system32\drivers\jraid.sys JMicron JMB36X RAID Driver
Hope it could help
++
jonedeuf: BEFORE you test, please go to your BIOS and make sure JMicron RAID is *disabled*. I'm now quite sure you've got this *enabled*, which is what would cause this BSOD.
Why is that? Because if you enable RAID, Windows will load the jraid driver, if you disable it, Windows will load the jahci driver. But it seems that if you enable RAID with just *one* HDD, the jraid driver will fail.
And make sure you use the latest bios.
Ok the test version works fine, no BSOD. After reading motherboard's notice, i've seen that the JMicron chipset is used only for Sata2 devices and for only 1 device, so no Raid possible. The Raid configuration is only available for sata1 devices (max 2 devices) and it's the Uli M1567 chipset which is used in this case. The Jmicron chipset is model 360 (No support for 'hot plug' functions), and i suppose that is a special config for this motherboard.
When entering in bios config, i've 2 choices for the Sata2 device: IDE mode and Sata2. When choosing IDE Mode, the notice says that no additional driver is required, but i had this mode enabled when BSOD appears at 1st boot...
I have the same problem. Same MB and BSOD.
Been trying to fix since Base 7012.
here is the Jmicron drivers...INF, CAT, SYS
http://rapidshare.com/files/13678361/JM … P.rar.html
I will wait a little bit then download the test and try it.
Last edited by bitman44 (2007-01-28 07:21:07)
I have the same problem. Same MB and BSOD.
Been trying to fix since Base 7012.here is the Jmicron drivers...INF, CAT, SYS
http://rapidshare.com/files/13678361/JM … P.rar.html
I will wait a little bit then download the test and try it.
You should try the nightly that muiz has posted, which has the work-around implemented for your motherboard.
no luck for me with the nightly test.
i still get BSOD 0x0000007b
chkdsk /r didn't help.
I have no floppy so slipping the driver packs is my option.
6 coasters 7 days. i am just really tired.
any help appreciated.
i am running with the sataII disconnected right now.
but i want to get my cluttered up machine onto my new sataII.
recommendations?
Can you post the driver you use for the floppy?
Can you post the driver you use for the floppy?
Yes. EDITED TO ADD the 2006 drivers
thanks it is at - http://rapidshare.com/files/13721994/JM … 05.2006.7z
Last edited by bitman44 (2007-01-28 14:28:25)
nothing here except link to ULI files
AGP AUDIO FIR IDE LAN SATA USB....
http://rapidshare.com/files/13723379/UL … s_v2.20.7z
Last edited by bitman44 (2007-01-28 14:01:49)
Just download the driver for your chip and put it on a floppy.
Try with the floppy to install.
The driver you posted is supported by the packs.
And post your HWIDS.
Last edited by muiz3 (2007-01-28 14:12:41)
Just download the driver for your chip and put it on a floppy.
Try with the floppy to install.
The driver you posted is supported by the packs.And post your HWIDS.
I would have to buy a floppy drive and cable. no thanks.
the HWIDS gives me a REV00 not REV02
EDITED..... so should i try that? p.s. - i noticed the new drivers (post #14) do not mention JAHCI in the INF file...will that matter.
===========
PCI devices
===========
PCI\VEN_10B9&DEV_5289&SUBSYS_52891849&REV_10\3&267A616A&0&91: ALi SATA/RAID Controller (M5289)
PCI\VEN_197B&DEV_2360&SUBSYS_03601849&REV_00\4&2FF59A88&0&0018: JMicron 20360/20363 AHCI Controller
Last edited by bitman44 (2007-01-28 14:41:30)
Hello, i think you should try to manually write that in txtsetup.sif:
PCI\VEN_197B&DEV_2360="jahci"
PCI\VEN_197B&DEV_2360&SUBSYS_03601849&REV_00="jahci"
PCI\VEN_197B&DEV_2360&CC_0104="jraid"
PCI\VEN_197B&DEV_2361&CC_0104="jraid"
PCI\VEN_197B&DEV_2363&CC_0104="jraid"
PCI\VEN_197B&DEV_2365&CC_0104="jraid"
PCI\VEN_197B&DEV_2366&CC_0104="jraid"
PCI\VEN_197B&DEV_2360&CC_0106="jraid"
PCI\VEN_197B&DEV_2361&CC_0106="jraid"
PCI\VEN_197B&DEV_2363&CC_0106="jraid"
PCI\VEN_197B&DEV_2365&CC_0106="jraid"
PCI\VEN_197B&DEV_2366&CC_0106="jraid"
Maybe the line for this motherboard could be:
PCI\VEN_197B&DEV_2360&SUBSYS_03601849="jahci"
i will try in the next hours
Ok, after testing this line in txtsetup.sif:
PCI\VEN_197B&DEV_2360&SUBSYS_03601849="jahci"
all works fine, no BSOD.
Bitman, maybe you can test it ?
muiz3, is it possible to have a test version with this line instead of :
PCI\VEN_197B&DEV_2360&SUBSYS_03601849&REV_02="jahci"
Thanks
@jonedeuf ,
i have uploaded the test version with the proposed PCI\VEN_197B&DEV_2360&SUBSYS_03601849 right here:
http://rapidshare.com/files/13784411/DP … ly.7z.html
Can you guys give it another go?
ok the last test version works fine, no BSOD. Thank you very much
@bitman44,
could you try this test version aswell?
@bitman44,
could you try this test version aswell?
IT WORKED.
With BASE 7015 i had no finisher errors.
Thankyou Very Much.
Last edited by bitman44 (2007-01-29 12:09:04)
ok problem solved , case closed
Powered by PunBB, supported by Informer Technologies, Inc.
Currently installed 3 official extensions. Copyright © 2003–2009 PunBB.
[ Generated in 0.034 seconds, 8 queries executed ]
