DriverPacks.net Forum - [REQ] nForce Raid / PnP Interface Fix

Re: [REQ] nForce Raid / PnP Interface Fix

2011-02-16T19:42:21Z

ATechGuy, I hadn't been there, and I hadn't done that. Thanks a lot! That fool proof gide was a godsend (or techguysend?).

Re: [REQ] nForce Raid / PnP Interface Fix

2010-09-18T06:03:29Z

bump

Re: [REQ] nForce Raid / PnP Interface Fix

2010-08-19T19:25:41Z

Well, you could try the test packs here: http://forum.driverpacks.net/viewtopic.php?id=4742
Specifically pack #13 & 14 (ideally, all of them) in both IDE mode and AHCI mode.
The more tests, the more accurate the packs will get.
Please report the results in the above thread.

Re: [REQ] nForce Raid / PnP Interface Fix

2010-08-19T18:37:20Z

I have an Acer SFF system with nForce 720A chipset and 8100 integrated nVidia graphics. I have suffered the lack of my beloved DriverPacks to support the AHCI SATA drive interface for a few months. But I complain NOT....

Instead I offer my time and experience to TEST any nightlies you deem fit for my consumption.

I remain at y'all's service.

THANK YOU!

Mark Strelecki
Atlanta GA.

Re: [REQ] nForce Raid / PnP Interface Fix

2010-08-18T20:02:51Z

I am working on getting these added to a nightly build.
Would you be willing to test?

Re: [REQ] nForce Raid / PnP Interface Fix

2010-06-19T18:25:30Z

Bump

Re: [REQ] nForce Raid / PnP Interface Fix

2009-06-29T20:21:26Z

Been there ... still on the todo list though... so i can't say i have done that... not yet...

Thanks for the update !~

Re: [REQ] nForce Raid / PnP Interface Fix

2009-06-29T13:45:15Z

These were the other instructions for adding the PNP driver. For Overflow, I'm sure this is "been there, done that". :-)

We now need to make modifications to the setup hive

Go start, run type regedit
Now, select HKEY_LOCAL_MACHINE right click and press File, Load Hive
Select I386/SETUPREG.HIV - name it whatever you want e.g. nvidia
Now open nvidia, CurrentControlSet001, services
Select services right click go create, new, key call it nvgts
Select nvgts right click go create, new, key call it Parameters
Sow select Parameters right click go create, new, key call it PnpInterface
Sow select PnpInterface right click go create, new, DWORD value
Replace New Value #1 with 5, right click 5, press modify and change Value Data to 1
Select nvidia and go file, unload hive - this saves the new SETUPREG.HIV

We now need to make modifications to the installation hive

open i386\HIVESYS.INF in a text editor
under:
Code:
HKLM,"SYSTEM\CurrentControlSet\Services\ultra\Parameters\PnpInterface","5",0x00010003,1
add:
Code:
HKLM,"SYSTEM\CurrentControlSet\Services\nvgts","ErrorControl",0x00010003,1
HKLM,"SYSTEM\CurrentControlSet\Services\nvgts","Group",0x00000002,"SCSI miniport"
HKLM,"SYSTEM\CurrentControlSet\Services\nvgts","Start",0x00010003,4
HKLM,"SYSTEM\CurrentControlSet\Services\nvgts","Tag",0x00010003,60
HKLM,"SYSTEM\CurrentControlSet\Services\nvgts","Type",0x00010003,1
HKLM,"SYSTEM\CurrentControlSet\Services\nvgts\Parameters",,0x00000012
HKLM,"SYSTEM\CurrentControlSet\Services\nvgts\Parameters\PnpInterface","5",0x00010003,1
save and exit
Remaining steps involve the $OEM$ folders: Create in the root of your installation source a folder called $OEM$, then inside of that a folder called $1 then inside of that one called Drivers, then another one called NVIDIA inside of Drivers in here place the sataraid and sata_ide folders that were inside the IDE folder of the extracted chipset drivers

Now you'll need to modify or create an WINNT.SIF mine looks as follows:
The important settings being OemPreinstall, UnattendedInstall, DriverSigningPolicy and OemPNPDriversPath
Code:
;SetupMgrTag
[Data]
AutoPartition=0
MsDosInitiated="0"
UnattendedInstall="Yes"

[Unattended]
UnattendMode=DefaultHide
OemPreinstall=Yes
OemSkipEula=Yes
TargetPath=\WINDOWS
FileSystem=*
Repartition=No
UnattendSwitch="No"
WaitForReboot="No"
DriverSigningPolicy=Ignore
OemPnPDriversPath="Drivers\NVIDIA\sataraid;Drivers\NVIDIA\sata_ide"

.....

Re: [REQ] nForce Raid / PnP Interface Fix

2009-06-29T13:42:58Z

Just a little more info on this missing nforce driver. 9.01 certainly doesn't include this driver. If you're still having problems finding it, look in:

http://www.nvidia.com/object/nforce_winxp_15.23.html

Bad me, I had to return the client's box and I hadn't run the hw_ids script on it, but I used another site which had the info in order to get my PE disk to run. I think there may be a few missing idents from an earlier entry in this thread so you might want to see if the list I have here has any you might not have added.

[SourceDisksFiles]
nvgts.sys = 100,,,,,,3_,4,1,,,1,4
nvrd32.sys = 100,,,,,,3_,4,1,,,1,4

[HardwareIdsDatabase]
PCI\VEN_10DE&DEV_0036 = "nvgts"
PCI\VEN_10DE&DEV_003E = "nvgts"
PCI\VEN_10DE&DEV_0054 = "nvgts"
PCI\VEN_10DE&DEV_0055 = "nvgts"
PCI\VEN_10DE&DEV_0266 = "nvgts"
PCI\VEN_10DE&DEV_0267 = "nvgts"
PCI\VEN_10DE&DEV_037E = "nvgts"
PCI\VEN_10DE&DEV_037F = "nvgts"
PCI\VEN_10DE&DEV_036F = "nvgts"
PCI\VEN_10DE&DEV_03F6 = "nvgts"
PCI\VEN_10DE&DEV_03F7 = "nvgts"
PCI\VEN_10DE&DEV_03E7 = "nvgts"
PCI\VEN_10DE&DEV_044C = "nvgts"
PCI\VEN_10DE&DEV_0558 = "nvgts"
PCI\VEN_10DE&DEV_0559 = "nvgts"
PCI\VEN_10DE&DEV_055A = "nvgts"
PCI\VEN_10DE&DEV_07F8 = "nvgts"
PCI\VEN_10DE&DEV_07F9 = "nvgts"
PCI\VEN_10DE&DEV_07FA = "nvgts"
PCI\VEN_10DE&DEV_07FB = "nvgts"
PCI\VEN_10DE&DEV_0AD9 = "nvgts"
PCI\VEN_10DE&DEV_0AD8 = "nvgts"
PCI\VEN_10DE&DEV_0ABD = "nvgts"
PCI\VEN_10DE&DEV_0ABC = "nvgts"
PCI\VEN_10DE&DEV_0BC4 = "nvgts"
PCI\VEN_10DE&DEV_0BC5 = "nvgts"
SCSI\NVIDIA__Raid_Disk________ = "nvrd32"
SCSI\__NVIDIA_______Raid_Disk = "nvrd32"
SCSI\NVIDIA__Raid_Disk_20_____ = "nvrd32"
SCSI\__NVIDIA____Raid_Disk_20 = "nvrd32"
*_NVRAIDBUS = "nvrd32"
*NVRAIDBUS = "nvrd32"
*NVRAID20 = "nvrd32"

[SCSI.load]
nvgts = nvgts.sys,4
nvrd32 = nvrd32.sys,4

[SCSI]
nvgts = "NVIDIA nForce Storage Controller"
nvrd32 = "NVIDIA RAID Driver"

Thanks!

Re: [REQ] nForce Raid / PnP Interface Fix

2009-03-28T00:00:29Z

Very cool... thanks for the idea...

You da man!

I have never gotten enough info/feedback to properly add this fix to base...
IE i still don't know if this fix is also required for 2k3...

Re: [REQ] nForce Raid / PnP Interface Fix

2009-03-27T22:08:02Z

@OverFlow
Yes, nvgts.sys is one of these PnpInterface driver.

I made a assumption:
add PnpInterface to all scsiport.sys and storport.sys device drivers.
Not verified at real hardware. Should work. No hardware to test.

Part of a batch

findstr.exe /m /I "scsiport.sys storport.sys" "%Target%\%%b.%%c" && (
reg.exe add "%Services%\%%b\Parameters\PnpInterface" /f /t REG_DWORD /v "5" /d 1 )

Re: [REQ] nForce Raid / PnP Interface Fix

2009-03-27T05:07:42Z

OH.... it's one of those?

Re: [REQ] nForce Raid / PnP Interface Fix

2009-03-26T20:23:49Z

@kambing

Try run setPnpInterfaceNvgts.cmd at \I386 directory:

copy setupreg.hiv setupreg.hiv.%random%.sav

reg.exe unload HKLM\loaded_SYSTEM
reg.exe load HKLM\loaded_SYSTEM setupreg.hiv

reg.exe add "HKLM\loaded_SYSTEM\ControlSet001\Services\nvgts\Parameters\PnpInterface" /f /t REG_DWORD /v "5" /d 1 
reg.exe add "HKLM\loaded_SYSTEM\ControlSet001\Services\nvgts5\Parameters\PnpInterface" /f /t REG_DWORD /v "5" /d 1 
reg.exe add "HKLM\loaded_SYSTEM\ControlSet001\Services\nvgts6\Parameters\PnpInterface" /f /t REG_DWORD /v "5" /d 1 
reg.exe add "HKLM\loaded_SYSTEM\ControlSet001\Services\nvgts7\Parameters\PnpInterface" /f /t REG_DWORD /v "5" /d 1 

reg.exe unload HKLM\loaded_SYSTEM

Re: [REQ] nForce Raid / PnP Interface Fix

2009-03-24T03:03:00Z

here link for massstorage driver
this is for raid
http://download.biostar.com.tw/upload/D … d_xp32.exe
this is for achi
http://download.biostar.com.tw/upload/D … e_xp32.exe

can u teach me how to add massstorage driver ,, i`m trying to add before but fail but with nlite ok..

this is what im trying edit

a) i`m replace \D\M\NV6\ with new driver
b) then i edit "DriverPack_MassStorage_wnt5_x86-32.ini" in the [nv6] section

 [NV6]
ms_count=1
ms_1_deviceName="NVIDIA AHCI DRIVER (SCSI)"
ms_1_tag="nvgts"
ms_1_sysFile="nvgts.sys"
ms_1_hwids="PCI\VEN_10DE&DEV_0036&CC_0101,PCI\VEN_10DE&DEV_003E&CC_0101,PCI\VEN_10DE&DEV_0054&CC_0101,PCI\VEN_10DE&DEV_0055&CC_0101,PCI\VEN_10DE&DEV_0266&CC_0101,PCI\VEN_10DE&DEV_0267&CC_0101,PCI\VEN_10DE&DEV_037E&CC_0101,PCI\VEN_10DE&DEV_037F&CC_0101,PCI\VEN_10DE&DEV_036F&CC_0101,PCI\VEN_10DE&DEV_03F6&CC_0101,PCI\VEN_10DE&DEV_03F7&CC_0101,PCI\VEN_10DE&DEV_03E7&CC_0101,PCI\VEN_10DE&DEV_044D&CC_0106,PCI\VEN_10DE&DEV_044E&CC_0106,PCI\VEN_10DE&DEV_044F&CC_0106,PCI\VEN_10DE&DEV_0554&CC_0106,PCI\VEN_10DE&DEV_0555&CC_0106,PCI\VEN_10DE&DEV_0556&CC_0106,PCI\VEN_10DE&DEV_07F4&CC_0106,PCI\VEN_10DE&DEV_07F5&CC_0106,PCI\VEN_10DE&DEV_07F6&CC_0106,PCI\VEN_10DE&DEV_07F7&CC_0106,PCI\VEN_10DE&DEV_0768&CC_0106,PCI\VEN_10DE&DEV_0AD5&CC_0106,PCI\VEN_10DE&DEV_0AD4&CC_0106,PCI\VEN_10DE&DEV_0AB9&CC_0106,PCI\VEN_10DE&DEV_0AB8&CC_0106,PCI\VEN_10DE&DEV_0BCC&CC_0106,PCI\VEN_10DE&DEV_0BCD&CC_0106"
ms_1_isBusExtender=false
ms_1_exc_disableIfOS="w2k"

anything wrong?

another question

i use nlite for slipstream massstorage driver, its works detect my hdd n complete windows installation... .without install any driver

but if i combine nlite + driverpack base. its fail .:( why?

Re: [REQ] nForce Raid / PnP Interface Fix

2009-03-24T00:30:36Z

Hi kambing, the driver your looking for is missing from our pack please provide us a link where we can download a working driver and I will add it asap.